THS3201_14 Datasheet, PDF (2/40 Pages) Texas Instruments – 1.8-GHz, LOW DISTORTION, CURRENT-FEEDBACK AMPLIFIER

THS3201
SLOS416C – JUNE 2003 – REVISED JUNE 2009 ............................................................................................................................................................. www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS
Over operating free-air temperature range unless otherwise noted.⁽¹⁾
V_S
V_I
I_O
V_ID
T_J
T_J
T_A
T_STG
ESD ratings
Supply voltage
Input voltage
Output current
Differential input voltage
Continuous power dissipation
Maximum junction temperature⁽²⁾
Maximum junction temperature, continuous operation, long term reliability⁽³⁾
Operating free-air temperature range
Storage temperature range
HBM
CDM
MM
UNIT
16.5 V
±V_S
175 mA
±3 V
See Dissipation Rating Table
+150°C
+125°C
–40°C to +85°C
–65°C to +150°C
3000 V
1500 V
100 V
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
(2) The absolute maximum ratings under any condition is limited by the constraints of the silicon process. Stresses above these ratings may
cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are
stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied.
(3) The maximum junction temperature for continuous operation is limited by package constraints. Operation above this temperature may
result in reduced reliability and/or lifetime of the device.
PACKAGE
DBV (5)
D (8)
DGN (8)⁽¹⁾
DGK (8 pin)
PACKAGE DISSIPATION RATINGS⁽¹⁾
θ_JC
(°C/W)
55
38.3
4.7
54.2
θ_JA ⁽²⁾
(°C/W)
255.4
97.5
58.4
260
POWER RATING⁽³⁾
(T_J = +125°C)
T_A ≤ +25°C
T_A= +85°C
391 mW
156 mW
1.02 W
410 mW
1.71 W
685 mW
385 mW
154 mW
(1) The THS3201 may incorporate a PowerPAD™ on the underside of the chip. This acts as a heat sink
and must be connected to a thermally dissipative plane for proper power dissipation. Failure to do so
may result in exceeding the maximum junction temperature which could permanently damage the
device. See TI technical briefs SLMA002 and SLMA004 for more information about utilizing the
PowerPAD thermally enhanced package.
(2) This data was taken using the JEDEC standard High-K test PCB.
(3) Power rating is determined with a junction temperature of +125°C. This is the point where distortion
starts to substantially increase. Thermal management of the final PCB should strive to keep the
junction temperature at or below +125°C for best performance and long term reliability.
RECOMMENDED OPERATING CONDITIONS
Supply voltage
T_A
Operating free-air temperature range
Dual supply
Single supply
MIN
MAX
UNIT
±3.3
±7.5
V
6.6
15
–40
+85
°C
2
Submit Documentation Feedback
Product Folder Link(s): THS3201
Copyright © 2003–2009, Texas Instruments Incorporated