CC2650 Datasheet, PDF (13/64 Pages) Texas Instruments – Multistandard Wireless MCU

www.ti.com
CC2650
SWRS158B – FEBRUARY 2015 – REVISED JULY 2016
5 Specifications
5.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)⁽¹⁾⁽²⁾
MIN
MAX UNIT
Supply voltage (VDDS, VDDS2,
and VDDS3)
VDDR supplied by internal DC-DC regulator or
internal GLDO. VDDS_DCDC connected to VDDS on
PCB.
–0.3
Supply voltage (VDDS⁽³⁾ and
VDDR)
External regulator mode (VDDS and VDDR pins
connected on PCB)
–0.3
Voltage on any digital pin⁽⁴⁾⁽⁵⁾
–0.3
4.1 V
2.25 V
VDDSx + 0.3, max 4.1 V
Voltage on crystal oscillator pins, X32K_Q1, X32K_Q2, X24M_N and X24M_P
–0.3
VDDR + 0.3, max 2.25 V
Voltage scaling enabled
–0.3
VDDS
Voltage on ADC input (V_in)
Voltage scaling disabled, internal reference
–0.3
Voltage scaling disabled, VDDS as reference
–0.3
1.49 V
VDDS / 2.9
Input RF level
5 dBm
T_stg
Storage temperature
–40
150 °C
(1) All voltage values are with respect to ground, unless otherwise noted.
(2) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(3) In external regulator mode, VDDS2 and VDDS3 must be at the same potential as VDDS.
(4) Including analog-capable DIO.
(5) Each pin is referenced to a specific VDDSx (VDDS, VDDS2 or VDDS3). For a pin-to-VDDS mapping table, see Table 6-3.
5.2 ESD Ratings
V_ESD
Electrostatic discharge
(ESD) performance
Human body model (HBM), per ANSI/ESDA/JEDEC
JS001 ⁽¹⁾
Charged device model (CDM), per JESD22-C101⁽²⁾
All pins
RF pins
Non-RF pins
VALUE
±2500
±750
±750
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
UNIT
V
5.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Ambient temperature range
Operating supply voltage
(VDDS and VDDR), external
regulator mode
For operation in 1.8-V systems
(VDDS and VDDR pins connected on PCB, internal DC-
DC cannot be used)
Operating supply voltage VDDS _{For operation in battery-powered and 3.3-V systems}
Operating supply voltages
VDDS2 and VDDS3
(internal DC-DC can be used to minimize power
consumption)
MIN
–40
1.7
1.8
0.7 × VDDS, min 1.8
MAX UNIT
85 °C
1.95 V
3.8 V
3.8 V
Copyright © 2015–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: CC2650
Specifications
13