TPS65916_17 Datasheet, PDF (1/89 Pages) Texas Instruments – 3.1-V to 5.2-V, 5 Buck Converter and 5 LDO Power Management IC (PMIC)

Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
TPS65916
SLVSD09B – MARCH 2016 – REVISED MARCH 2017
TPS65916 3.1-V to 5.2-V, 5 Buck Converter and 5 LDO Power Management IC (PMIC)
1 Device Overview
1.1 Features
1
• System Voltage Range from 3.135 V to 5.25 V
• Low-Power Consumption
– 20 μA in Off Mode
– 90 μA in Sleep Mode With Two SMPSs Active
• Five Step-Down Switched-Mode Power Supply
(SMPS) Regulators:
– 0.7- to 3.3-V Output Range in 10- or 20-mV
Steps
– Two SMPS Regulators With 3.5-A Capability,
With the Ability to Combine into 7-A Output in
Dual-Phase Configuration, With Differential
Remote Sensing (Output and Ground)
– Three Other SMPS Regulators with 3-A, 2-A,
and 1.5-A Capabilities
– Dynamic Voltage Scaling (DVS) Control and
Output Current Measurement in 3.5-A and 3-A
SMPS Regulators
– Hardware and Software Controlled Eco-mode™
Supplying up to 5 mA
– Short-Circuit Protection
– Power-Good Indication (Voltage and
Overcurrent Indication)
– Internal Soft-Start for In-Rush Current Limitation
– Ability to Synchronize to External Clock between
1.7 MHz and 2.7 MHz
• Five Low-Dropout (LDO) Linear Regulators:
– 0 .9- to 3.3-V Output Range in 50-mV steps
– Two With 300-mA Capability and Bypass Mode
– One With 100-mA Capability and Capable of
Low-Noise Performance up to 50 mA
– Two Other LDOs With 200-mA Current
Capability
– Short-Circuit Protection
• 12-Bit Sigma-Delta General-Purpose ADC
(GPADC) With 8 Input Channels (2 external)
• Thermal Monitoring With High Temperature
Warning and Thermal Shutdown
• Power Sequence Control:
– Configurable Power-Up and Power-Down
Sequences (OTP)
– Configurable Sequences Between the SLEEP
and ACTIVE State Transition (OTP)
– Three Digital Output Signals that can be
Included in the Startup Sequence
• Selectable Control Interface:
– One SPI for Resource Configurations and DVS
Control
– Two I²C Interfaces.
– One Dedicated for DVS Control
– One General Purpose I²C Interface for
Resource Configuration and DVS Control
• OTP Bit-Integrity Error Detection With Options to
Proceed or Hold Power-Up Sequence and
RESET_OUT Release
• Package Option:
– 7-mm × 7-mm 48-pin VQFN With 0.5-mm Pitch
1.2 Applications
• Industrial Automation
• Human Machine Interface (HMI)
• Camera Surveillance System
• Programmable Logic Controller (PLC)
• Factory Automation
1.3 Description
The TPS65916 PMIC integrates five configurable step-down converters with up to 3.5 A of output current
to power the processor core, memory, I/O, and preregulation of LDOs The step-down converters are
synchronized to an internal 2.2-MHz clock to improve EMC performance of the device. The GPIO_3 pin
allows the step-down converters to synchronize to an external clock, allowing multiple devices to
synchronize to the same clock which improves system-level EMC performance. The device also contains
five LDOs to power low-current or low-noise domains.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.