BQ24195 Datasheet, PDF (6/41 Pages) Texas Instruments – I2C Controlled 2.5A / 4.5A Single Cell USB/Adapter Charger With 5.1V at 1A / 5.1V at 2.1A Synchronous Boost Operation

bq24195
bq24195L
SLUSB97 – OCTOBER 2012
www.ti.com
PIN
NAME
PGND
SW
BTST
REGN
PMID
PowerPAD
PIN FUNCTIONS (continued)
NO.
17,18
19,20
21
22
23
–
TYPE
P
O
Analog
P
P
P
P
DESCRIPTION
Power ground connection for high-current power converter node. Internally, PGND is connected to the source of the n-
channel LSFET. On PCB layout, connect directly to ground connection of input and output capacitors of the charger. A
single point connection is recommended between power PGND and the analog GND near the IC PGND pin.
Switching node connecting to output inductor. Internally SW is connected to the source of the n-channel HSFET and the
drain of the n-channel LSFET. Connect the 0.047µF bootstrap capacitor from SW to BTST.
PWM high side driver positive supply. Internally, the BTST is connected to the anode of the boost-strap diode. Connect
the 0.047µF bootstrap capacitor from SW to BTST.
PWM low side driver positive supply output. Internally, REGN is connected to the cathode of the boost-strap diode. For
VBUS above 6V, connect 1-µF ceramic capacitor from REGN to analog GND. For VBUS below 6V, connect a 4.7-μF
(10V rating) ceramic capacitor from REGN to analog GND. The capacitor should be placed close to the IC. REGN also
serves as bias rail of TS1 and TS2 pins.
Battery Boost Mode Output Voltage. Connected to the drain of the reverse blocking MOSFET and the drain of HSFET.
The minimum capactiance required on PMID to PGND is 20uF (bq24195L) or 60uF (bq24195)
Exposed pad beneath the IC for heat dissipation. Always solder PowerPAD™ to the board, and have vias on the Power
Pad plane star-connecting to PGND and ground plane for high-current power converter.
ABSOLUTE MAXIMUM RATINGS
Voltage range (with respect to GND)
Output sink current
Junction temperature
Storage temperature
VBUS
PMID, STAT,
BTST
SW
BAT, SYS (converter not switching)
SDA, SCL, INT, OTG, ILIM, REGN, TS1, TS2, CE, D+, D–
BTST TO SW
PGND to GND
INT, STAT
VALUE
–2 V – 20 V
–0.3 V –20 V
–0.3 V – 26 V
–2 V – 20 V
–0.3 V – 6 V
–0.3 V – 7 V
–0.3 V – 7 V
–0.3 V – 0.3 V
6mA
–40°C to 150°C
–65°C to 150°C
RECOMMENDED OPERATING CONDITIONS
V_IN Input voltage
I_IN
Input current
I_SYS Output current (SYS)
MIN
MAX
UNIT
3.9
17 ⁽¹⁾
V
3
A
4.5 (bq24195)
A
2.5 (bq24195L)
V_BAT Battery voltage
Fast charging current
I_BAT
Discharging current with internal MOSFET
4.4
V
4.5 (bq24195)
A
2.5 (bq24195L)
6 continuous
9 peak
A
(up to 1 sec duration)
T_A
Operating free-air temperature range
–40
85
°C
(1) The inherent switching noise voltage spikes should not exceed the absolute maximum rating on either the BTST or SW pins. A tight
layout minimizes switching noise.
6
Submit Documentation Feedback
Product Folder Links: bq24195 bq24195L
Copyright © 2012, Texas Instruments Incorporated