TS3DV416_09 Datasheet, PDF (5/18 Pages) Texas Instruments – 4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH FOR DVI/HDMI APPLICATIONS

www.ti.com
TS3DV416
4-CHANNEL DIFFERENTIAL 8:16 MULTIPLEXER SWITCH
FOR DVI/HDMI APPLICATIONS
SCDS198C – OCTOBER 2005 – REVISED MAY 2006
Electrical Characteristics⁽¹⁾
for high-frequency switching over recommended operating free-air temperature range, V_DD = 3.3 V ± 0.3 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP⁽²⁾ MAX UNIT
V_IK
I_IH
I_IL
I_off
I_DD
C_IN
C_OFF
C_ON
r_on
r_on(flat) ⁽³⁾
∆r_on ⁽⁴⁾
SEL
SEL
SEL
SEL
B port
V_DD = 3.6 V,
V_DD = 3.6 V,
V_DD = 3.6 V,
V_DD = 0,
V_DD = 3.6 V,
f = 1 MHz,
V_I = 0,
V_I = 0,
V_DD = 3 V,
V_DD = 3 V,
V_DD = 3 V,
I_IN = –18 mA
V_IN = V_DD
V_IN = GND
V_O = 0 to 3.6 V,
I_I/O = 0,
V_IN = 0
f = 1 MHz,
f = 1 MHz,
1.5 V ≤ V_I ≤ V_DD,
V_I = 1.5 V and V_DD,
1.5 V ≤ V_I ≤ V_DD,
V_I = 0
Switch ON or OFF
Outputs open,
Outputs open,
I_O = –40 mA
I_O = –40 mA
I_O = –40 mA
Switch OFF
Switch ON
–0.7 –1.2 V
±1 µA
±1 µA
1 µA
250 600 µA
2.5
3 pF
3.5
4 pF
10 10.9 pF
4
8Ω
0.7
Ω
0.2 1.2 Ω
(1) V_I, V_O, I_I, and I_O refer to I/O pins. V_IN refers to the control inputs.
(2) All typical values are at V_DD = 3.3 V (unless otherwise noted), T_A = 25°C.
(3) r_on(flat) is the difference of r_on in a given channel at specified voltages.
(4) ∆r_on is the difference of r_on from center (A₄, A₅) ports to any other port.
Switching Characteristics
over recommended operating free-air temperature range, V_DD = 3.3 V ± 0.3 V, R_L = 200 Ω, C_L = 10 pF
(unless otherwise noted) (see Figure 4 and Figure 5)
PARAMETER
t_pd ⁽²⁾
t_PZH, t_PZL
t_PHZ, t_PLZ
t_sk(o) ⁽³⁾
t_sk(p) ⁽⁴⁾
FROM
(INPUT)
A or B
SEL
SEL
A or B
TO
(OUTPUT)
B or A
A or B
A or B
B or A
MIN
TYP⁽¹⁾ MAX UNIT
0.04
ns
1.5
11.5 ns
1
8.5 ns
0.1 0.2 ns
0.1 0.2 ns
(1) All typical values are at V_DD = 3.3 V (unless otherwise noted), T_A = 25°C.
(2) The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load
capacitance when driven by an ideal voltage source (zero output impedance).
(3) Output skew between center port (A₄ to A₅) to any other port
(4) Skew between opposite transitions of the same output in a given device |t_PHL– t_PLH|
Dynamic Characteristics
over recommended operating free-air temperature range, V_DD = 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
X_TALK
O_IRR
BW
R_L = 100 Ω,
R_L = 100 Ω,
See Figure 6
f = 250 MHz,
f = 250 MHz,
See Figure 7
See Figure 8
TYP ⁽¹⁾
–41
–39
900
UNIT
dB
dB
MHz
(1) All typical values are at V_DD = 3.3 V (unless otherwise noted), T_A = 25°C.
Submit Documentation Feedback
5