SN74AUC2G53_09 Datasheet, PDF (3/20 Pages) Texas Instruments – SINGLE-POLE DOUBLE-THROW (SPDT) ANALOG SWITCH OR 2:1 ANALOG MULTIPLEXER/DEMULTIPLEXER

SN74AUC2G53
www.ti.com ................................................................................................................................................ SCES484C – AUGUST 2003 – REVISED JANUARY 2009
Absolute Maximum Ratings⁽¹⁾
over operating free-air temperature range (unless otherwise noted)
V_CC
Supply voltage range⁽²⁾
V_I
Input voltage range⁽²⁾⁽³⁾
V_I/O
Switch I/O voltage range⁽²⁾⁽³⁾
I_IK
Control input clamp current
I_I/OK
I/O port diode current
I_T
On-state switch current current
Continuous current through V_CC or GND
θ_JA
Package thermal impedance⁽⁴⁾
T_stg
Storage temperature range
V_I < 0
V_I/O < 0 or V_I/O > V_CC
V_I/O = 0 to V_CC
DCT package
DCU package
YZP package
MIN
MAX
–0.5
3.6
–0.5
3.6
–0.5 V_CC + 0.5
–50
50
50
100
220
227
102
–65
150
UNIT
V
V
V
mA
mA
mA
mA
C/W
C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to ground unless otherwise specified.
(3) The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
(4) The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions⁽¹⁾
V_CC
Supply voltage
V_IH
High-level input voltage
V_IL
Low-level input voltage
V_I/O
I/O port voltage
V_I
Control input voltage
Δt/Δv Input transition rise or fall rate
T_A
Operating free-air temperature
V_CC = 0.8 V
V_CC = 1.1 V to 1.95 V
V_CC = 2.3 V to 2.7 V
V_CC = 0.8 V
V_CC = 1.1 V to 1.95 V
V_CC = 2.3 V to 2.7 V
V_CC = 0.8 V to 1.6 V
V_CC = 1.65 V to 1.95 V
V_CC = 2.3 V to 2.7 V
MIN
0.8
V_CC
0.65 × V_CC
1.7
0
0
–40
MAX UNIT
2.7 V
V
0
0.35 × V_CC
0.7
V_CC
3.6
20
10
3.5
85
V
V
V
ns/V
C
(1) All unused inputs of the device must be held at V_CC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
r_on
On-state switch resistance
r_on(p)
Peak on resistance
TEST CONDITIONS
V_I = V_CC or GND,
V_INH = V_IL
(see Figure 1 and
Figure 2)
I_S = 4 mA
I_S = 8 mA
V_I = V_CC to GND,
V_INH = V_IL
(see Figure 1 and
Figure 2)
I_S = 4 mA
I_S = 8 mA
V_CC
1.1 V
1.65 V
2.3 V
1.1 V
1.65 V
2.3 V
MIN TYP⁽¹⁾
12.5
6
131
32
15
MAX UNIT
40
20 Ω
15
180
80 Ω
20
(1) T_A = 25C
Copyright © 2003–2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): SN74AUC2G53