BQ27510-G1 Datasheet, PDF (3/39 Pages) Texas Instruments – System-Side Impedance Track™ Fuel Gauge With Direct Battery Connection

bq27510-G1
www.ti.com ..................................................................................................................................................................................................... SLUS927 – APRIL 2009
ELECTRICAL SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)⁽¹⁾
V_REGIN
V_CC
V_IOD
V_BAT
V_I
T_F
T_STG
ESD
Regulator input voltage
Supply voltage range
Open-drain I/O pins (SDA, SCL, BAT_LOW/BAT_GD)
BAT input pin
Input voltage range to all other pins (TS, SRP, SRN, BI/TOUT)
Functional temperature range
Storage temperature range
Human Body Model (HBM), BAT pin
Human Body Model (HBM), all other pins
VALUE
–0.3 to 24
–0.3 to 2.75
–0.3 to 6
–0.3 to 6
–0.3 to V_CC + 0.3
–40 to 100
–65 to 150
1.5
2
UNIT
V
V
V
V
V
°C
°C
KV
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATINGS
PACKAGE
12-pin DRZ⁽¹⁾
T_A ≤ 40°C
POWER RATING
482 mW
DERATING FACTOR
T_A ≤ 40°C
5.67 mW/°C
R_θJA
176°C/W
(1) This data is based on using a 4-layer JEDEC high-K board with the exposed die pad connected to a Cu pad on the board. The board
pad is connected to the ground plane by a 2- x 2-via matrix.
RECOMMENDED OPERATING CONDITIONS
T_A = 25°C and V_REGIN += V_BAT = 3.6 V (unless otherwise noted)
PARAMETER
TEST CONDITION
V_REGIN
Supply voltage
No operating restrictions
No FLASH writes
I_CC
I_SLP
I_HIB
V_OL
V_OH(PP)
V_OH(OD)
V_IL
V_IH(OD)
V_A1
V_A2
V_A3
t_PUCD
Normal operating mode current
Low-power operating mode current
Hibernate operating mode current
Output voltage low (Pins 1, 10, 11, 12)
Output high voltage (Pin 1)
Output high voltage (Pins 10, 11, 12)
Input voltage low (Pins 1, 10, 11, 12)
Input voltage high (Pins 1, 10, 11, 12)
Input voltage range (TS)
Input voltage range (BAT)
Input voltage range (SRP, SRN)
Power-up communication delay
Fuel gauge in NORMAL mode,
I_LOAD > Sleep Current
Fuel gauge in SLEEP mode.
I_LOAD < Sleep Current
Fuel gauge in HIBERNATE mode.
I_LOAD < Hibernate Current
I_OL = 3 mA
I_OH = –1 mA
External pull-up resistor connected to Vcc
MIN
2.7
2.45
V_CC–0.5
V_CC–0.5
–0.3
1.2
V_SS–0.125
V_SS–0.125
V_SS–0.125
TYP
103
18
4
250
MAX
5.5
2.7
UNIT
V
µA
µA
µA
0.4
V
V
V
0.6
V
6
V
2
V
5
V
0.125
V
ms
POWER-ON RESET
T_A = –40°C to 85°C, C_REG = 0.47 µF, 2.45 V < V_REGIN = V_BAT < 5.5 V; typical values at T_A = 25°C and V_REGIN = V_BAT = 3.6 V
(unless otherwise noted)
V_IT+
V_HYS
PARAMETER
Positive-going battery voltage input at V_CC
Power-on reset hysteresis
TEST CONDITIONS
MIN TYP MAX UNIT
2.05 2.20 2.31 V
45 115 185 mV
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq27510-G1
Submit Documentation Feedback
3