BQ24040 Datasheet, PDF (3/31 Pages) Texas Instruments – 800mA Single-Input Single Cell Li-Ion Battery Charger With Auto Start

bq24040
bq24041
www.ti.com.................................................................................................................................... SLUS941A – SEPTEMBER 2009 – REVISED SEPTEMBER 2009
RECOMMENDED OPERATING CONDITIONS⁽¹⁾
V_IN
I_IN
I_OUT
T_J
R_PRE-TERM
R_ISET
R_TS
IN voltage range
IN operating voltage range, Restricted by V_DPM and V_OVP
Input current, IN pin
Current, OUT pin
Junction temperature
Programs precharge and termination current thresholds
Fast-charge current programming resistor
10k NTC thermistor range without entering BAT_EN or TTDM
(1) Operation with V_IN less than 4.5V or in drop-out may result in reduced performance.
MIN
3.5
4.45
0
1
0.675
1.66
NOM
28
6.45
0.8
0.8
125
10
49.9
258
UNIT
V
V
A
A
°C
kΩ
kΩ
kΩ
ELECTRICAL CHARACTERISTICS
Over junction temperature range 0°C ≤ T_J ≤ 125°C and recommended supply voltage (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
INPUT
UVLO
V_{HYS_UVLO}
V_IN-DT
V_HYS-INDT
t_{DGL(PG_PWR)}
t_{DGL(PG_NO-}
PWR)
V_OVP
t_DGL(OVP-SET)
V_HYS-OVP
t_DGL(OVP-REC)
Undervoltage lock-out Exit
Hysteresis on V_{UVLO_RISE} falling
Input power good detection threshold
is V_OUT + V_IN-DT
Hysteresis on V_IN-DT falling
Deglitch time on exiting sleep.
Deglitch time on V_HYS-INDT power
down. Same as entering sleep.
Input over-voltage protection threshold
Input over-voltage blanking time
Hysteresis on OVP
Deglitch time exiting OVP
V_IN: 0V → 4V Update based on sim/char
V_IN: 4V→0V,
V_{UVLO_FALL} = V_{UVLO_RISE} –V_HYS-UVLO
(Input power good if V_IN > V_OUT + V_IN-DT); V_OUT =
3.6V, V_IN: 3.5V → 4V
V_OUT = 3.6V, V_IN: 4V → 3.5V
Time measured from V_IN: 0V → 5V 1μs rise-time
to PG = low, V_OUT = 3.6V
Time measured from V_IN: 5V → 3.2V 1μs fall-time
to PG = OC, V_OUT = 3.6V
V_IN: 5V → 12V (bq24040)
V_IN: 5V → 12V (bq24041)
V_IN: 5V → 12V
V_IN: 11V → 5V
Time measured from V_IN: 12V → 5V 1μs fall-time
to PG = LO
3.15
175
30
6.5
6.9
3.3
227
80
31
45
29
6.65
7.1
113
95
30
V_IN-DPM
USB/Adaptor low input voltage
protection. Restricts lout at V_IN-DPM
Feature active in USB mode; Limit Input Source
Current to 50mA; V_OUT=3.5V; R_ISET = 825Ω
Feature active in Adaptor mode; Limit Input
Source Current to 50mA; V_OUT=3.5V; R_ISET =
4.34
4.24
4.4
4.3
825Ω
USB input I-Limit 100mA
I_IN-USB-CL
USB input I-Limit 500mA, bq24040
USB input I-Limit 380mA, bq24041
ISET SHORT CIRCUIT TEST
ISET2 = Float; R_ISET = 825Ω
ISET2 = High; R_ISET = 825Ω
ISET2 = High; R_ISET = 825Ω
85
92
430
462
350
386
R_{ISET_SHORT}
Highest Resistor value considered a Riset: 600Ω → 250Ω, Iout latches off. Cycle
fault (short). Monitored for Iout>90mA power to Reset.
280
t_{DGL_SHORT}
Deglitch time transition from ISET
short to Iout disable
Clear fault by cycling IN or TS/BAT_EN
1
I_{OUT_CL}
Maximum OUT current limit Regulation V_IN = 5V, V_OUT = 3.6V, V_ISET2 =Low, Riset: 600Ω
(Clamp)
→ 250Ω, Iout latches off after t_DGL-SHORT
1.05
MAX UNIT
3.45 V
280 mV
145 mV
mV
μs
ms
6.8
V
7.3
μs
mV
μs
4.46
V
4.36
100
500 mA
420
500 Ω
ms
1.4 A
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq24040 bq24041
Submit Documentation Feedback
3