71M6521DE Datasheet, PDF (37/101 Pages) Teridian Semiconductor Corporation – Energy Meter IC

71M6521DE/71M6521FE
Energy Meter IC
DATASHEET
JANUARY 2008
On-Chip Resources
Oscillator
The 71M6521DE/FE oscillator drives a standard 32.768kHz watch crystal. These crystals are accurate and do not require a
high-current oscillator circuit. The 71M6521DE/FE oscillator has been designed specifically to handle these crystals and is
compatible with their high impedance and limited power handling capability.
PLL and Internal Clocks
Timing for the device is derived from the 32.768kHz oscillator output. On-chip timing functions include the MPU master clock, a
real time clock (RTC), and the delta-sigma sample clock. In addition, the MPU has two general counter/timers (see MPU
section).
The ADC master clock, CKADC, is generated by an on-chip PLL. It multiplies the oscillator output frequency (CK32) by 150.
The CE clock frequency is always CK32 * 150, or 4.9152MHz, where CK32 is the 32kHz clock. The MPU clock frequency is
determined by MPU_DIV and can be 4.9152MHz *2^-MPU_DIV Hz where MPU_DIV varies from 0 to 7 (MPU_DIV is 0 on power-
up). This makes the MPU clock scalable from 4.9152MHz down to 38.4kHz. The circuit also generates a 2x MPU clock for use
by the emulator. This clock is not generated when ECK_DIS is asserted by the MPU.
The setting of MPU_DIV is maintained when the device transitions to BROWNOUT mode, but the time base in BROWNOUT
mode is 28,672Hz.
Real-Time Clock (RTC)
The RTC is driven directly by the crystal oscillator. It is powered by the net V2P5NV (battery-backed up supply). The RTC
consists of a counter chain and output registers. The counter chain consists of seconds, minutes, hours, day of week, day of
month, month, and year. The RTC is capable of processing leap years. Each counter has its own output register. Whenever
the MPU reads the seconds register, all other output registers are automatically updated. Since the RTC clock is not coherent
to the MPU clock, the MPU must read the seconds register until two consecutive reads are the same (requires either 2 or 3
reads). At this point, all RTC output registers will have the correct time. Regardless of the MPU clock speed, RTC reads
require one wait state.
RTC time is set by writing to the RTC registers in I/O RAM. Each byte written to RTC must be delayed at least 3 RTC cycles
from any previous byte written to RTC. Hardware RTC write protection requires that a write to address 0x201F occur before
each RTC write. Writing to address 0x201F opens a hardware ‘enable gate’ that remains open until an RTC write occurs and
then closes. It is not necessary to disable interrupts between the write operation to 0x201F and the RTC write because the
‘enable gate’ will remain open until the RTC write finally occurs
Two time correction bits, RTC_DEC_SEC and RTC_INC_SEC are provided to adjust the RTC time. A pulse on one of these bits
causes the time to be decremented or incremented by an additional second at the next update of the RTC_SEC register. Thus,
if the crystal temperature coefficient is known, the MPU firmware can integrate temperature and correct the RTC time as
necessary.
Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap reference. The MPU may
request an alternate multiplexer frame containing the temperature sensor output by asserting MUX_ALT. The primary use of
the temperature data is to determine the magnitude of compensation required to offset the thermal drift in the system (see
section titled “Temperature Compensation”).
v1.0
© 2005-2008 TERIDIAN Semiconductor Corporation
Page: 37 of 101