English
Language : 

TL071_16 Datasheet, PDF (7/51 Pages) Texas Instruments – Low-Noise JFET-Input Operational Amplifiers
www.ti.com
TL071, TL071A, TL071B
TL072, TL072A, TL072B, TL074, TL074A, TL074B
SLOS080M – SEPTEMBER 1978 – REVISED JUNE 2015
6.6 Electrical Characteristics, TL07xM
VCC± = ±15 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS(1)
VIO
Input offset voltage
VO = 0, RS = 50 Ω
αVIO
Temperature coefficient
of input offset voltage
VO = 0, RS = 50 Ω
IIO
Input offset current
VO = 0
IIB
Input bias current
VO = 0
VICR
VOM
AVD
B1
ri
CMRR
kSVR
ICC
VO1/VO2
Common-mode input
voltage range
Maximum peak output
voltage swing
Large-signal differential
voltage amplification
RL = 10 kΩ
RL ≥ 10 kΩ
RL ≥ 2 kΩ
VO = ±10 V, RL ≥ 2 kΩ
Unity-gain bandwidth
Input resistance
Common-mode
rejection ratio
Supply-voltage rejection
ratio (ΔVCC±/ΔVIO)
Supply current
(each amplifier)
VIC = VICRmin,
VO = 0, RS = 50 Ω
VCC = ±9 V to ±15 V,
VO = 0, RS = 50 Ω
VO = 0, No load
Crosstalk attenuation AVD = 100
TA (2)
25°C
Full range
Full range
25°C
Full range
25°C
25°C
25°C
Full range
25°C
25°C
25°C
25°C
25°C
TL071M, TL072M
MIN
TYP
MAX MIN
3
6
9
TL074M
TYP
3
MAX
9
15
UNIT
mV
18
18
μV/°C
5
100
20
65
200
50
5
100 pA
20 nA
65
200 pA
20 nA
±11 –12 to 15
±11 –12 to 15
V
±12
±13.5
±12
±10
35
200
15
3
1012
±12
±13.5
±12
±10
35
200
15
3
1012
V
V/mV
MHz
Ω
80
86
80
86
dB
80
86
80
86
dB
1.4
2.5
120
1.4
2.5 mA
120
dB
(1) Input bias currents of an FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as
shown in Figure 1. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as
possible.
(2) All characteristics are measured under open-loop conditions with zero common-mode voltage, unless otherwise specified. Full range is
TA = –55°C to 125°C.
6.7 Switching Characteristics
VCC± = ±15 V, TA= 25°C
PARAMETER
TEST CONDITIONS
SR
tr
Vn
In
THD
Slew rate at unity
gain
Rise-time overshoot
factor
VI = 10 V,
CL = 100 pF,
VI = 20 V,
CL = 100 pF,
Equivalent input noise
voltage
RS = 20 Ω
Equivalent input noise
current
RS = 20 Ω,
Total harmonic
distortion
VIrms = 6 V,
RL ≥ 2 kΩ,
f = 1 kHz,
RL = 2 kΩ,
See Figure 20
RL = 2 kΩ,
See Figure 20
f = 1 kHz
f = 10 Hz to 10 kHz
f = 1 kHz
AVD = 1,
RS ≤ 1 kΩ,
TL07xM
MIN TYP MAX
5
13
0.1
20%
18
4
0.01
TL07xC, TL07xAC,
TL07xBC, TL07xI
MIN TYP MAX
UNIT
8
13
V/μs
0.1
20%
18
4
μs
nV/√Hz
μV
0.01
pA/√Hz
0.003%
0.003%
Copyright © 1978–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: TL071 TL071A TL071B TL072 TL072A TL072B TL074 TL074A TL074B