SKY77176 Datasheet, PDF (3/11 Pages) Skyworks Solutions Inc. – AutoSmart Dual-Band Power Amplifier Module for CDMA/PCS(824-849 MHz and 1850-1910 MHz)

AUTOSMART™ DUAL-BAND POWER AMPLIFIER MODULE
FOR CDMA/PCS (824–849 MHZ AND 1850–1910 MHZ)
PRELIMINARY DATA SHEET • SKY77176
Table 4. Electrical Specifications for CDMA Cell Nominal Operating Conditions ¹
Characteristics
Symbol
Condition
Minimum
Typical
Maximum
Unit
Gain Conditions
GLOW
PO_D ≤ 0 dBm
—
Digital Mode
GHIGH
PO_D = 28 dBm
—
Analog Mode
GP
PO_A = 31 dBm
—
PAED_LOW PO_D = 16 dBm
—
Power Added Efficiency
Digital Mode
(VCC = 3.4 V)
PAED_HIGH PO_D = 28 dBm
—
Analog Mode
PAEa
PO_A = 31 dBm
—
Total Supply Current
ICC_LOW
PO_D = 16 dBm
—
ICC_HIGH
PO_D = 28 dBm
—
Total Supply Current in Power-down Mode
IPD
VCC = 3.4 V
VREF = 0 V
—
Quiescent Current
ICQ
—
Reference Current
IREF
—
Adjacent Channel Power ^2,3
885 kHz offset ACP1
PO_D ≤ 28 dBm
—
1.98 MHz offset ACP2
—
Second
f02
—
Harmonic Suppression
PO_D ≤ 31 dBm
Third
f03
—
Noise Power in RX Band 869-894 MHz
RxBN
PO_D ≤ 28 dBm
—
Noise Figure
NF
—
Input Voltage Standing Wave Ratio
VSWR
—
Stability (Spurious output)
Ruggedness—No damage ⁴
S
5:1 VSWR
all phases
—
Ru
PO_D ≤ 28 dBm
10:1
Turn On Time ⁵
DC
TONDC
—
RF
TONRF
—
Turn Off Time ⁵
DC
TOFFDC
—
RF
TOFFRF
—
21.0
—
28.0
—
dB
27.0
—
9
—
40
—
%
55
—
130
—
mA
450
—
2.0
—
μA
20
—
mA
1.0
—
mA
–49
—
dBc
–60
—
–35
—
dBc
–55
—
–139
—
dBm/Hz
4.0
—
dB
2.0:1
—
–70.0
dBc
—
—
VSWR
40
—
μs
5
—
40
—
μs
5
—
1 _{Per Table 2 over dynamic range up to 28 dBm output power, unless otherwise specified.}
2 _{ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW.}
3 _{For CDMA2000 test configured as [PCH @ –3.75 dB, DCCH–9600 bps @ 0 dB; SCHO–9600 bps @ 0 dB] and other test configurations that yield a peak-to-average up to 4.5 dB for CCDF = 1%,}
up to 1. dB power back off from the maximum listed for IS95 may be required to meet specified maximum ACP performance under worst-case conditions.
4 _{All phases, time = 10 seconds.}
5 _{TONDC is time required to reach stable quiescent bias (±10%) after VREF is switched high.}
TOFFDC is time required for battery to decrease to < 100 μA after VREF is switched low.
After ICQ is stable, The TONRF is time to reach final output power (±1 dB) once RF input is applied.
TOFFRF is time required for PO to drop 30 dB once RF input is removed.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
200409A • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • November 17, 2007
3