SKY66104-11 Datasheet, PDF (3/14 Pages) Skyworks Solutions Inc. – 1787 to 1930 MHz High-Power RF Front-End Module

DATA SHEET • SKY66104-11: HIGH-POWER RF FEM
Table 2. SKY66104-11 Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Minimum
Maximum
Units
Supply voltage (VCC1, VCC2, VDD)
VPS
–0.3
+4.8
V
Logic control voltages
VIH, VIL
–0.3
+3.3
V
Transmit RF input power (at TX port)
PIN_TX
+10
dBm
Receive RF input power (at ANT1 or ANT2 ports)
PIN_RX
+20
dBm
Voltage standing wave ratio
VSWR
6:1
–
Operating case temperature (Note 2)
TC
–40
+85
C
Storage temperature
TSTG
–55
+150
C
Electrostatic discharge:
ESD
Human Body Model (HBM), Class 1A
250
V
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their typical value as provided in Tables 3, 4, and 5. Exceeding any of the limits listed here may result in permanent damage to the device.
Note 2: Nominal junction-to-case thermal resistance is 80C/W.
CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. SKY66104-11 Recommended Operating Conditions
Parameter
Symbol
Minimum
Operating case temperature (Note 1)
TC
–40
RF supply voltage (Note 2)
VCC1, VCC2
3.0
Switch supply voltage (Note 2)
VDD
3.0
Note 1: Specified case temperature is measured at the MCM ground pad interface.
Note 2: Power supply pins VCC1, VCC2, and VDD are independent supplies and are not internally tied together.
Typical
+25
3.6
3.6
Maximum
+80
4.5
4.5
Units
C
V
V
Table 4. SKY66104-11 DC Electrical Specifications (Note 1)
(VCC1/2 = +3.6 V, VDD = 3.6 V, TC = +25 C, PIN = 0 dBm, as Measured on the SKY66104-11 Evaluation Board (De-Embedded to Device),
Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
Total supply current in Transmit Mode
(Note 2)
IPS(TX24)
IPS(TX15)
POUT = +24 dBm
POUT = +15 dBm
171
mA
83
mA
IPS(TX10)
POUT = +10 dBm
58
mA
Total supply current in Receive Mode
(Note 2) (Note 3)
IPS(RX)
60
μA
Total supply current in Sleep Mode
(Note 2) (Note 3)
IPS(OFF)
4.1
μA
NTP input current in Transmit Mode (Note 3) INTP_IN
9.5
μA
Note 1: Performance is guaranteed only under the conditions listed in this Table. Receive (RX), Transmit (TX), and Sleep Mode configurations are defined in Table 9. Typical performance shown
is for Engineering Sample 2 (ES2).
Note 2: IPS = ICC1 + ICC2 + IDD. These are expected total power supply currents for indicated POUT at ANT1/2 ports.
Note 3: NTP = 0 V.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
202908C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 9, 2014
3