SKY16602-632LF Datasheet, PDF (3/11 Pages) Skyworks Solutions Inc. – Low limiting threshold

DATA SHEET ● SKY16602-632LF: LOW-THRESHOLD PIN DIODE LIMITER
Electrical and Mechanical Specifications
The absolute maximum ratings of the SKY16602-632LF are
provided in Table 2. Electrical specifications for the un-tuned
limiter module are provided in Table 3, and typical performance
characteristics are illustrated in Figures 4 and 5. Electrical
specifications for the 2.45 GHz tuned limiter module are
provided in Table 4, and typical performance characteristics are
illustrated in Figures 6 and 7.
Figures 8 and 9 show the power derating curves for the limiter.
In Figure 8, the temperature is referenced to the bottom of the
QFN package. The power derating curve with the temperature
referenced to the bottom of the printed circuit board is shown in
Figure 9.
Table 2. SKY16602-632LF Absolute Maximum Ratings¹
Parameter
Symbol
Minimum
Maximum
Unit
RF input power (CW) at TCASE = 85C
PIN
12
W
RF input power (1 s pulse, 10% duty cycle) at TCASE = 85C
PIN
120
W
CW power dissipation at TCASE = 85C
PDIS
0.4
W
Storage temperature
TSTG
−65
150
°C
Operating temperature
TOP
−40
85
°C
Electrostatic discharge:
ESD
Charged-Device Model (CDM), Class 4
Human Body Model (HBM), Class 1B
Machine Model (MM), Class A
1000
V
250
V
150
V
1 _{Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set}
at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although these devices are designed to be as robust as possible, electrostatic discharge (ESD) can damage them. These
devices must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human
body or equipment, which can discharge without detection. Industry-standard ESD precautions should be employed at all
times.
Table 3. SKY16602-632LF Electrical Specifications (Untuned Circuit, Reference Figure 1)
(TOP = 25C, ZO = 50 , as Measured in Skyworks Evaluation Board Optimized for Operation at 0.2 to 4.0 GHz, Unless Otherwise Noted)
Parameter
Symbol
Condition
Frequency
Min.
Typ.
Max.
Units
Reverse voltage
VR
20
V
Forward current
IF
50
mA
Insertion loss
IL
PIN = 0 dBm
0.90 GHz
0.3
0.5
dB
Return loss
RL
PIN = 0 dBm
0.90 GHz
14
dB
Threshold level
Saturated CW input power¹
Flat leakage power²
Recovery time³
TL
PIN_CW
FL
tR
P1dB
PIN = +10 dBm
0.90 GHz
0.90 GHz
0.90 GHz
0.90 GHz
5.3
6.0
6.7
dBm
30
dBm
6
dBm
5
ns
Thermal resistance
JC
Junction-to-case
114
C/W
1 _{Saturated CW input power is defined as the point where the diode series resistance does not change with the rectified current. As the input power increases past this point, output power will}
increase until the diode reaches its max power limit.
2 _{Flat leakage power is defined as the power level after the limiter has fully turned on and the output pulse reaches a constant level.}
3 _{Recovery time represents the transition time from the high-loss to low-loss state following the removal of high-power input. RF pulse modulation: 1 s pulse width and 0.1% duty factor.}
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
202945F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 11, 2016
3