EFM32TG230 Datasheet, PDF (49/68 Pages) Silicon Laboratories – Output state retention and wake-up from Shutoff Mode

...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality 0
1
2
3
4
5
6
Description
ACMP1_O
PF2
PD7
Analog comparator ACMP1, digital output.
ADC0_CH0
PD0
Analog to digital converter ADC0, input channel number 0.
ADC0_CH1
PD1
Analog to digital converter ADC0, input channel number 1.
ADC0_CH2
PD2
Analog to digital converter ADC0, input channel number 2.
ADC0_CH3
PD3
Analog to digital converter ADC0, input channel number 3.
ADC0_CH4
PD4
Analog to digital converter ADC0, input channel number 4.
ADC0_CH5
PD5
Analog to digital converter ADC0, input channel number 5.
ADC0_CH6
PD6
Analog to digital converter ADC0, input channel number 6.
ADC0_CH7
PD7
Analog to digital converter ADC0, input channel number 7.
BOOT_RX
PE11
Bootloader RX.
BOOT_TX
PE10
Bootloader TX.
CMU_CLK0
PA2
PC12 PD7
Clock Management Unit, clock output number 0.
CMU_CLK1
PA1
PD8
PE12
Clock Management Unit, clock output number 1.
DAC0_N0 /
OPAMP_N0
PC5
Operational Amplifier 0 external negative input.
DAC0_N1 /
OPAMP_N1
PD7
Operational Amplifier 1 external negative input.
OPAMP_N2
PD3
Operational Amplifier 2 external negative input.
DAC0_OUT0 /
OPAMP_OUT0
PB11
Digital to Analog Converter DAC0_OUT0 /
OPAMP output channel number 0.
DAC0_OUT0ALT /
OPAMP_OUT0ALT
PC0
PC1
PC2 PC3
PD0
Digital to Analog Converter DAC0_OUT0ALT /
OPAMP alternative output for channel 0.
DAC0_OUT1 /
OPAMP_OUT1
PB12
Digital to Analog Converter DAC0_OUT1 /
OPAMP output channel number 1.
DAC0_OUT1ALT /
OPAMP_OUT1ALT
PC12
PC13
PC14 PC15
PD1
Digital to Analog Converter DAC0_OUT1ALT /
OPAMP alternative output for channel 1.
OPAMP_OUT2 PD5
PD0
Operational Amplifier 2 output.
DAC0_P0 /
OPAMP_P0
PC4
Operational Amplifier 0 external positive input.
DAC0_P1 /
OPAMP_P1
PD6
Operational Amplifier 1 external positive input.
OPAMP_P2
PD4
Operational Amplifier 2 external positive input.
DBG_SWCLK
PF0
PF0
Debug-interface Serial Wire clock input.
Note that this function is enabled to pin out of reset, and has
a built-in pull down.
DBG_SWDIO
PF1
PF1
Debug-interface Serial Wire data input / output.
Note that this function is enabled to pin out of reset, and has
a built-in pull up.
DBG_SWO
PF2
PC15
Debug-interface Serial Wire viewer Output.
Note that this function is not enabled after reset, and must be
enabled by software to be used.
GPIO_EM4WU0 PA0
Pin can be used to wake the system up from EM4
GPIO_EM4WU1 PA6
Pin can be used to wake the system up from EM4
GPIO_EM4WU2 PC9
Pin can be used to wake the system up from EM4
GPIO_EM4WU3 PF1
Pin can be used to wake the system up from EM4
GPIO_EM4WU4 PF2
Pin can be used to wake the system up from EM4
GPIO_EM4WU5 PE13
Pin can be used to wake the system up from EM4
2015-03-06 - EFM32TG230FXX - d0030_Rev1.40
49
www.silabs.com