LC87F1JJ8B Datasheet, PDF (23/28 Pages) Sanyo Semicon Device – 8-bit 1-chip Microcontroller with USB-host controller

LC87F1JJ8B
Continued from preceding page.
Parameter
HALT mode
consumption
current
(Note 7-1)
HOLD mode
consumption
current
Symbol
IDDHALT(11)
IDDHALT(12)
IDDHALT(13)
IDDHOLD(1)
IDDHOLD(2)
IDDHOLD(3)
Pin/
Remarks
VDD1
=VDD2
=VDD3
VDD1
Conditions
• HALT mode
• FmCF=0Hz (oscillation stopped)
• FsX'tal=32.768kHz crystal oscillation mode
• System clock set to crystal oscillation side
(32.768kHz)
• Internal RC oscillation stopped
• 1/2 frequency division ratio
• HOLD mode
• CF1=VDD or open (External clock mode)
VDD[V]
min
4.5 to 5.5
3.0 to 3.6
2.7 to 3.0
4.5 to 5.5
3.0 to 3.6
2.7 to 3.0
Specification
typ
max
unit
31
132
9.1
53
6.3
42
0.24
72
μA
0.12
38
0.11
33
Timer HOLD
IDDHOLD(4)
• Timer HOLD mode
4.5 to 5.5
26
115
mode
consumption
current
IDDHOLD(5)
IDDHOLD(6)
• CF1=VDD or open (External clock mode)
• FsX’tal=32.768kHz crystal oscillation mode
3.0 to 3.6
2.7 to 3.0
6.1
50
3.8
40
Note 7-1: The consumption current value includes none of the currents that flow into the output Tr and internal pull-up
resistors.
USB Characteristics and Timing at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Conditions
Specification
min
typ
max
unit
High level output
VOH(USB)
• 15kΩ±5% to GND
2.8
3.6
V
Low level output
VOL(USB)
• 1.5kΩ±5% to 3.6V
0.0
0.3
V
Output signal crossover voltage
VCRS
1.3
2.0
V
Differential input sensitivity
VDI
• ⏐(UHD+)-(UHD-)⏐
0.2
V
Differential input common mode range
VCM
0.8
2.5
V
High level input
VIH(USB)
2.0
V
Low level input
VIL(USB)
0.8
V
USB data rise time
tR
• RS=33Ω, CL=50pF
4
20
ns
USB data fall time
tF
• RS=33Ω, CL=50pF
4
20
ns
F-ROM Programming Characteristics at Ta = +10°C to +55°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Onboard programming
current
IDDFW(1)
Pin/
Remarks
VDD1
Conditions
• Excluding power dissipation in the
microcontroller block
VDD[V]
3.0 to 5.5
Specification
min typ max unit
5
10 mA
Programming time
tFW(1)
tFW(2)
• Erase operation
• Write operation
3.0 to 5.5
20
30 ms
40
60 μs
Main System Clock Oscillation
The constant values of the oscillator and oscillation circuit for the main and system clocks must be determined after
exercising extensive oscillation evaluation tests. For an application in which the USB host function is to be used, use an
oscillator having the accuracy and precision that satisfy the USB specifications.
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized in the
following cases (see Figure 4):
• Till the oscillation gets stabilized after VDD goes above the operating voltage lower limit.
• Till the oscillation gets stabilized after the instruction for starting the main clock oscillation circuit is executed.
• Till the oscillation gets stabilized after the HOLD mode is released.
• Till the oscillation gets stabilized after the X'tal HOLD mode is released with CFSTOP (OCR register, bit 0) set to 0.
No.A1538-23/28