LC87F1JJ8B Datasheet, PDF (21/28 Pages) Sanyo Semicon Device – 8-bit 1-chip Microcontroller with USB-host controller

LC87F1JJ8B
Pulse Input Conditions at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Conditions
High/low level tPIH(1) INT0(P70), INT1(P71), • Interrupt source flag can be set.
Specification
VDD[V]
min
typ
max
unit
pulse width
tPIL(1)
INT2(P72),
• Event inputs for timer 0 or 1 are
INT4(P20 to P23),
INT5(P24 to P27),
enabled.
2.7 to 5.5
1
INT6(P20),
INT7(P24)
tPIH(2) INT3(P73) when noise • Interrupt source flag can be set.
tPIL(2)
filter time constant is
• Event inputs for timer 0 are
2.7 to 5.5
2
tCYC
1/1
enabled.
tPIH(3) INT3(P73) when noise • Interrupt source flag can be set.
tPIL(3)
filter time constant is
• Event inputs for timer 0 are
2.7 to 5.5
64
1/32
enabled.
tPIH(4) INT3(P73) when noise • Interrupt source flag can be set.
tPIL(4)
filter time constant is
• Event inputs for timer 0 are
2.7 to 5.5
256
1/128
enabled.
tPIL(5)
RMIN(P73)
Recognized by the infrared remote
2.7 to 5.5
4
control receiver circuit as a signal
RMCK
(Note 5-1)
tPIL(6)
RES
Resetting is enabled.
2.7 to 5.5
200
μs
Note 5-1: Represents the period of the reference clock (1 tCYC to 128 tCYC or the source frequency of the subclock)
for the infrared remote control receiver circuit.
AD Converter Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = VSS3 = 0V
Parameter
Symbol
Pin/Remarks
Resolution
Absolute
accuracy
Conversion time
N
ET
TCAD
AN0(P00) to
AN7(P07),
AN8(P70),
AN9(P71),
AN10(XT1),
AN11(XT2)
Conditions
(Note 6-1)
AD conversion time=32×tCYC
(when ADCR2=0) (Note 6-2)
VDD[V]
3.0 to 5.5
3.0 to 5.5
4.5 to 5.5
min
15.68
(tCYC=
0.490µs)
Specification
typ
max
unit
8
bit
±1.5 LSB
97.92
(tCYC=
3.06µs)
23.52
97.92
3.0 to 5.5
(tCYC=
(tCYC=
AD conversion time=64×tCYC
0.735µs)
18.82
3.06µs)
μs
97.92
(when ADCR2=1) (Note 6-2)
4.5 to 5.5
(tCYC=
(tCYC=
0.294µs)
1.53µs)
47.04
97.92
3.0 to 5.5
(tCYC=
(tCYC=
0.735µs)
1.53µs)
Analog input
voltage range
VAIN
3.0 to 5.5
VSS
VDD
V
Analog port
IAINH
VAIN=VDD
3.0 to 5.5
input current
IAINL
VAIN=VSS
3.0 to 5.5
-1
Note 6-1: The quantization error (±1/2LSB) is excluded from the absolute accuracy.
1
μA
Note 6-2: The conversion time refers to the period from the time when an instruction for starting a conversion process is
issued to the time the conversion results register(s) are loaded with a complete digital conversion value
corresponding to the analog input value.
No.A1538-21/28