LC8766C8A Datasheet, PDF (13/23 Pages) Sanyo Semicon Device – 8-Bit Single Chip Microcontroller

LC8766C8A/B2A/96A
3. Electrical Characteristics at Ta=-30°C to +70°C, VSS1=VSS2=0V
Parameter
Input high
current
Input low
current
Output high
voltage
Output low
voltage
Pull-up
resistor
Symbol
IIH(1)
IIH(2)
IIH(3)
IIH(4)
IIH(5)
IIH(6)
IIH(7)
IIL(1)
IIL(2)
IIL(3)
IIL(4)
IIL(5)
VOH(1)
VOH(2)
VOH(3)
VOH(4)
VOH(5)
VOH(6)
VOH(7)
VOL(1)
VOL(2)
VOL(3)
Rpu
Ratings
Pins
Conditions
unit
VDD[V] min. typ. max.
Ports 0,3: N-ch open •Output disabled
4.5–6.0
5 µA
drain output
•VIN=13.5V
(including OFF state leak
current of the output Tr.)
Port 0,1,3,7,8
•Output disabled
4.5–6.0
1
•Pull-up resister OFF.
•VIN=VDD
(including OFF state leak
current of the output Tr.)
S16 to S51 without When configured as an input 4.5–6.0
60
pull-down resister port
(Port C,D,E,F,G)
VIN=VDD
RES
VIN=VDD
4.5–6.0
1
XT1,XT2
When configured as an input 4.5–6.0
1
port
VIN=VDD
CF1
VIN=VDD
4.5–6.0
15
P87/AN7/MICIN VIN=VBIS+0.5V
4.5–6.0 4.2
8.5 15
weak signal input (VBIS : Bias voltage)
Port 0,1,3,7,8
•Output disabled
4.5–6.0 -1
•VIN=VSS
(including OFF state leak
current of the output Tr.)
RES
VIN=VSS
4.5–6.0 -1
XT1,XT2
When configured as an input 4.5–6.0 -1
port
VIN=VSS
CF1
VIN=VSS
4.5–6.0 -15
P87/AN7/MICIN VIN=VBIS-0.5V
4.5–6.0 -15 -8.5 -4.2
weak signal input (VBIS : Bias voltage)
Port 0,1,3: CMOS IOH=-1.0mA
4.5–6.0 VDD-1
V
output option
IOH=-0.1mA
4.5–6.0 VDD-0.5
Port 7
IOH=-0.4mA
4.5–6.0 VDD-1
S0/T0–S15/T15
IOH=-20.0mA
4.5–6.0 VDD-1.8
IOH=-1.0mA
4.5–6.0 VDD-1
IOH at any single pin is not
over 1mA.
S2+ to S51
IOH=-5.0mA
4.5–6.0 VDD-1.8
IOH=-1.0mA
4.5–6.0 VDD-1
IOH at any single pin is not
over 1mA.
Port 02, 03
IOL=30mA
4.5–6.0
1.5
Port 0,1,3
IOL=10mA
4.5–6.0
1.5
IOL=1.6mA
4.5–6.0
0.4
Port 0,1,3,7
VOH=0.9VDD
4.5–6.0 15
40 70 kΩ
Continued
No.6718-13/23