CS0603C0G104B6R3NRA Datasheet, PDF (13/14 Pages) SAMWHA ELECTRIC – Multi Layer Ceramic Capacitors

No.
Item
Characteristic
Temperature
Compensating Type
High Dielectric Constant Type
Test Methods
and Conditions
7. Resistance Appearance No marked defect
to
Soldering
Heat
Capacitance
Change
Within 2.5% or 0.25pF X7R :
(whichever is larger) Z5U, Y5V :
7.5%
20%
Dissipation 30 Min. :
Char. 50V Min. 25V 16V 10V
Factor(or Q) Q 1,000 (DF 0.1%)
X7R 2.5% 3% 3.5% 5.0%
30 Max. :
Q 400 20C
(DF 1/(400 20C))
Z5U 4.0%
5%
(<220 )
Y5V _7%
( 220 )
9%
(<220 )
7% _12.5%
( 220 )
12.5%
- Soldering Temp : 260 5
- Immersion Time : 5 0.5sec
- Take it out and set it for 24 2
hours(temperature compensating
type)or 48 4hours(high dielectric
constant type) then measure.
I.R.
8. Temperature Appearance
Cycle
Capacitance
Change
Dissipation
Factor(or Q)
More than 10,000 or 500 (whichever & smaller)
No marking defects
Within 2.5% or 0.25pF X7R : Within + 7.5%
Z5U, Y5V : Within 20%
30 Min. :
Q 1,000 (DF 0.1%)
30 Max. :
Q 400 20C
(DF 1/(400 20C))
Char. 50V Min. 25V
X7R 2.5% 3%
16V 10V
3.5% 5.0%
Z5U 4.0%
5%
(<220 )
Y5V _7%
( 220 )
9%
(<220 )
7% _12.5%
( 220 )
12.5%
Step 1
2
3
4
Min.
Max.
Temp. Operating Room Operating Room
( ) Temp. Temp. emp. Temp.
0, 3
3, 0
Time
(min)
30 3
2 to 3 30 3 2 to 3
Take it out and set it for 24 2 hours
[tempeature compensating or 48 4
hours(high dielectric Type) at room
temperature, than measure.
I.R.
More than 10,000 or 500 (Whichever is smaller)
9. Humidity
Load
Appearance No marking defects
Capacitance
Change
Within 7.5% or 0.75
(whichever is larger)
X7R : Within 12.5%
Z5U : Within 30%
Y5V : Within 30%, 40%
(Y5V/1.0 F, 2.2 F, 4.7 F/10V)
Within 30% (others)
Dissipation _{30 Min. :}
Factor(or Q) _{Q 200 (DF 0.5%)}
30 Max. :
Q 100 10/3C
(DF 1/(100 10/3C))
Char. 50V Min. 25V 16V 10V
X7R 5% 5% 5% 5%
Z5U 4.0%
10%
(<1 )
Y5V 7.5% _12.5% 12.5% 15%
(1)
- Temperature : 40 2
- Humidity : 90~95%RH
- Hour : 500 12hrs
- Test Voltage : Tge rated voltage
- Take it out and set it for 24 2 hours
(temperature compensatig) or 48 4
hours(high dielectric constant type)
at room temperature, then measure.
The charge/discharge current is less
than 50mA.
I.R.
More than 500 or 25 (whichever is smaller)
10. High
Appearance
Temperature
Load
Capacitance
change
No marked defect
Within 3% or 0.3
(whichever is larger)
X7R : Within 12.5% , Z5U : Within 30%
Y5V : Within 30%(Cap. < 1.0 F)
Within +30% , 40%(Cap. 1.0 F)
- Testing Time : 1000 12hrs
- Applied Voltage : Rated Voltage 200%
- Temperature :
C0G, X7R 125 3
Z5U, Y5V 85 3
SAMWHA CAPACITOR Co., Ltd.
Radial & Axial
No.
Item
Characteristic
Temperature
Compensating Type
High Dielectric Constant Type
10 High
Dissipation
Temperature _{Factor(or Q)}
Load
I.R.
30 Min. :
Q 350 (DF 0.3%)
10
30
Q 275 5/2C
(DF 1/(275 5/2C))
10 Max. :
Q 200 10C
(DF 1/(200 10C))
Char. 50V Min. 25V 16V 10V
X7R 5% 5% 5% 5%
Z5U 4.0%
10%
Y5V
7.5%
(<1 )
7%
12.5% 15%
( 1)
More than 1000 or 50 (Whichever is smaller)
11 Capacitance Capacitance
Temperature Change
Characteristics
Char.
X7R
Z5U
Y5V
Temp.
Range
55 to
125
10 to
85
30 to
85
Reference
Temp.
25
Cap.
Change
Within
15%
Within
22%
56%
Within
22%
82%
Test Methods
and Conditions
Take it out and set it for 24 2 hours
(temperature compensatig) or 48 4
hours(high dielectric constant type)
at room temperature, then measure.
The charge/discharge current is less
than 50mA.
(1) Temperature Compensating Type :
The temperature coefficient is
determined using the capacitance
measured in step 3 as a reference.
When cycling the temperature
sequentially from step 1 through 5.
(SL: +25 to 85 ) the capacitance shall
be with in the specified tolerance for
the temperature coefficient.
The capacitance drift is calculated
dividing the difference between the
maximum measured values in the
step 1, 3 and 5 by Cap, value in step 3.
Temperature
Coefficient
Temp. Temperature
Char. _{Range Coefficient}
C0G ^{55 to} 30ppm/
125
Step
Temperature
1
25 2
2
-55 3
3
25 2
4
125 3(for C0G)
5
25 2
12 The regulation of
environmental
pollution materials
(2) High Dielectric Constant Type :
The ranges of capacitance
change compared with the 25
value over the temperature
range shown in the table shall
be in the specified range.
Never use materials mentioned below in leaded MLCC products regulated this document.
Pb, Cd, Hg, Cr⁺⁶, PBB(polybromida biphenyl), PBDE(polybrominated diphenyl ethers), asbestos.
13 The regulation about
destructive materials
of the ozone layer
Never use the ODS(ozone depleting substance) materials below in leaded MLCC products
regulated this document.
Packing Quantity
Inner Box
2,500
Radial Type
Outer Box
Remark
15,000 Packing set on the basis of flat tapping
Inner Box
5,000
Unit : pcs
Axial Type
Outer Box
Remark
50,000 Packing set on the basis of flat tapping
Multi Layer Ceramic Capacitors