BU24033GW_16 Datasheet, PDF (14/25 Pages) Rohm – u - step System Lens Driver for Digital Still Cameras

BU24033GW
●Serial interface
Control commands are framed by a 16-bit serial input (MSB first) and are sent through CSB, SCLK, and SDATA pins.
The 4 higher-order bits specify addresses, while the remaining 12 bits specify data. Data of every bit is sent through SDATA
pin, which is retrieved during the rising edge of SCLK. Data becomes valid when CSB is Low and is registered during the
rising edge of CSB. Furthermore, the interface will be synchronized with the falling edges of SCLK to output the SOUT data
of the 12 bits.
CSB
SCLK
SDATA x D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 x
SOUT
Hiz
Address
x
Data
D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
Hiz
＜Register map＞
Address[3:0]
15 14 13 12
0000
0001
0010
0011
0100
0101
0110
0111
1011
1100
1101
1110
11
10
9
8
7
A_Mode[1:0]
A_SEL[2:0]
0
0
0
0
0
0
1
0
0
1
1
0 A_BEXC
1
1
1
0
0
A_EN A_RT
A_ACT A_BUSY B_ACT B_BUSY L
B_Mode[1:0]
B_SEL[2:0]
0
0
0
0
0
0
1
0
0
1
1
0 B_BEXC
1
0
0
0
0
1
0
1
3_State_CTL[1:0]
1
1
0
4_State_CTL[1:0]
1
1
1
0
0
B_EN B_RT
A_Position[9:6]
0
0
0
0
0
0
0
1
0
0
0
0
Chopping[1:0] CacheM
0
0
0
0
0
0
0
1
0
0
0
1
0
5_State_CTL[1:0]
0
1
1
0
0
1
1
1
0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
1
0
0
1
1
0
0
0
Data[11:0]
6
5
4
3
2
1
0
A_different_output_voltage[6:0]
A_Cycle[5:0]
0
0
A_Cycle[13:6]
0
0
A_BSL A_AEXC 0
0
A_ASL
0
A_POS[1:0]
0
0
A_PS A_Stop
A_Pulse[9:0]
L
L
L
L
L
L
L
B_different_output_voltage[6:0]
B_Cycle[5:0]
0
0
B_Cycle[13:6]
0
0
B_BSL B_AEXC 0
0
B_ASL
0
3_CHOP[1:0]
0
0
4_CHOP[1:0]
3_PWM_Duty[6:0]
4_PWM_Duty[6:0]
0
B_POS[1:0]
0
0
B_PS B_Stop
B_Pulse[9:0]
B_ Position [9:6]
L
L
L
L
0
Edge
0
0
0
B_CTL A_CTL
0
0
0
0
EXT_CTL[2:0]
0
0 CLK_EN
CLK_DIV[3:0]
0
0
0
0
0 PI_CTL2 PI_CTL1
0
0 5_SPEN 0
0
5_CHOP[1:0]
5_PWM_Duty[6:0]
5_TARSP[7:0]
5_PSP[2:0]
0
5_ISP[2:0]
0
0
0
0
0
SPC_Limit[1:0]
6_IOUT[7:0]
0
0
0
0
0
6_State_CTL[1:0]
0
0
0
0
HYS3 HYS2 HYS1
0
0
STB
0
0 STM_RS CMD_RS
Addresses other
than those above
Setting prohibited
(Note 1) The notations A B in the register map correspond to Ach and Bch respectively. Ach is defined as 1ch and 2ch driver, Bch as 3ch and 4ch driver.
(Note 2) After reset (Power ON reset), the initial condition is saved in all registers.
(Note 3) The addresses 4’b0011, and 4’b0111 have data (ACT, BUSY, Position [9:6]), which are internal register values and output from SOUT pin.
(Note 4) For Mode, different output voltage, Cycle, EN, and RT registers, data that are written before the access to the Pulse register becomes valid and
determines the rising edge of CSB after the access to the Pulse register.
(The Mode, different output voltage, Cycle, EN, RT, and Pulse registers contain Cache registers. Any registers other than those do not contain Cache
registers.)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
14/21
TSZ02201-0M3M0BC16060-1-2
20.May.2016 Rev.003