HYS72T32000HP Datasheet, PDF (25/53 Pages) Qimonda AG – 240-Pin Registered DDR2 SDRAM Modules

Internet Data Sheet
HYS72T[32/64]xxxHP–[3S/3.7]–A
Registered DDR2 SDRAM Modules
Parameter
Symbol
DDR2–533
Min.
Max.
Unit
Note^1)2)3)4)5)
6)7)
Data hold skew factor
Average periodic refresh Interval
t_QHS
—
t_REFI
—
—
Auto-Refresh to Active/Auto-Refresh
t_RFC
75
command period
400
ps
7.8
µs
14)15)
3.9
µs
16)21)
—
ns
17)
Auto-Refresh to Active/Auto-Refresh
t_RFC
105
command period
—
ns
18)
Auto-Refresh to Active/Auto-Refresh
t_RFC
127.5
—
command period
ns
19)
Auto-Refresh to Active/Auto-Refresh
t_RFC
197.5
—
command period
ns
20)
Precharge-All (4 banks) command period
Precharge-All (8 banks) command period
Read preamble
Read postamble
Active bank A to Active bank B command
period
t_RP
t_RP
t_RPRE
t_RPST
t_RRD
t_RP + 1t_CK
15 + 1tCK
0.9
0.40
7.5
10
—
—
1.1
0.60
—
—
ns
ns
t_CK
14)
t_CK
14)
ns
14)21)
ns
16)23)
Internal Read to Precharge command delay
Write preamble
Write postamble
Write recovery time for write without Auto-
Precharge
t_RTP
t_WPRE
t_WPST
t_WR
7.5
—
0.25 x t_CK
0.40
—
0.60
15
—
ns
t_CK
t_CK
22)
ns
Write recovery time for write with Auto-
WR
Precharge
t_WR/t_CK
t_CK
23)
Internal Write to Read command delay
t_WTR
7.5
Exit power down to any valid command
t_XARD
2
(other than NOP or Deselect)
—
ns
24)
—
t_CK
25)
Exit active power-down mode to Read
t_XARDS
6 – AL
—
command (slow exit, lower power)
t_CK
25)
Exit precharge power-down to any valid
t_XP
2
command (other than NOP or Deselect)
—
t_CK
Exit Self-Refresh to non-Read command
t_XSNR
t_RFC +10
—
ns
Exit Self-Refresh to Read command
t_XSRD
200
—
t_CK
1) For details and notes see the relevant QIMONDA component data sheet
2) V_DDQ = 1.8 V ± 0.1 V; V_DD = 1.8 V ±0.1 V. See notes ^5)6)7)8)
3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down
and then restarted through the specified initialization sequence before normal operation can continue.
4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS/ RDQS,
input reference level is the crosspoint when in differential strobe mode.
6) Inputs are not recognized as valid until V_REF stabilizes. During the period before V_REF stabilizes, CKE = 0.2 x V_DDQ is recognized as low.
7) The output timing reference voltage level is V_TT.
Rev. 1.01, 2006-09
25
03292006-ZZHP-PR83