CM300E3Y6-24NFH Datasheet, PDF (4/4 Pages) Powerex Power Semiconductors – Chopper IGBTMOD NFH-Series Module 300 Amperes/1200 Volts

Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 [phone] www.pwrx.com
CM300E3Y6-24NFH
Chopper IGBTMOD™ NFH-Series Module
300 Amperes/1200 Volts
Electrical Characteristics, T_j = 25°C unless otherwise specified
NTC Thermistor Part
Characteristics
Zero Power Resistance
Deviation of Resistance
B Constant
Power Dissipation
Symbol
R₂₅
∆R/R
B_(25/50)
P₂₅
Test Conditions
T_C = 25°C^*3
R₁₀₀ = 493Ω, T_C = 100°C^*3
Approximate by Equation^*5
T_C = 25°C^*3
Min.
Typ.
Max. Units
4.85 5.00 5.15
kΩ
-7.3
—
+7.8
%
—
3375
—
K
—
—
10
mW
Mechanical Characteristics
Mounting Torque
M_t
Mounting Torque
M_s
Weight
m
Flatness of Baseplate
e_c
Main Terminals, M6 Screw
Mounting, M6 Screw
On Centerline X, Y^*6
31
35
40
in-lb
31
35
40
in-lb
—
400
— Grams
-100
—
+100
µm
Thermal Resistance Characteristics, T_j = 25°C unless otherwise specified
Thermal Resistance, Junction to Case
R_th(j-c)Q
Per Inverter IGBT^*3
Thermal Resistance, Junction to Case
R_th(j-c)D
Per Inverter FWDi^*3
Thermal Resistance, Junction to Case
R_th(j-c)D
Per ClampDi^*3
Contact Thermal Resistance,
R_th(c-s)
Thermal Grease Applied,
Case to Heatsink^*2
per 1/2 Module^*3,*7
—
—
0.071
—
—
0.43
—
—
0.11
—
0.02
—
*3 Case temperature (T_C) is measured on the surface (mounting side) of the baseplate just under the chips.
Refer to the figure to the right for chip location.
*5
B_(25/50) = In(RR₅₂₀₅)/(T₂¹₅
1
– _T50
)
0
60.1
0
0
R₂₅; Resistance at Absolute Temperature T₂₅ [K]; T₂₅ = 25 [°C] + 273.15 = 298.15 [K]
R₅₀; Resistance at Absolute Temperature T₅₀ [K]; T₅₀ = 50 [°C] + 273.15 = 323.15 [K]
18.4
*6 Baseplate (mounting side) flatness measurement points (X, Y) are shown in the figure.
Th
Di1
24.4
32.2
Tr2
Tr2
Di2
Di1
34.5
34.4
Y _BOTTOM
3 mm
X
HEATSINK SIDE
HEATSINK SIDE
– CONCAVE
+ CONVEX
*7 Typical value is measured by using thermally conductive grease of λ = 0.9 [W/(m • K)].
0
31.8 42.2 52.4
76.7
LABEL SIDE
Each mark points to the center position of each chip.
Tr2: IGBT Di2: FWDi
Di1: ClampDi Th: NTC Thermistor
K/W
K/W
K/W
K/W
4
12/11 Rev. 0