HZZ00101 Datasheet, PDF (5/9 Pages) Power-One – Cassette Style Mating Connectors

Accessories
Cassette Style Mating Connectors H11, H15, H15S2, H15S4
H15S2, H15S4 Connectors
This special connectors derive from the H15 connectors
having 7 standard contacts as above, combined with 2
(H15S2) or 4 (H15S4) high current contacts (jacks)
according to DIN 41626. These jacks are specially
designed to handle currents from 20 A up to 40 A. They
correspond to quality class 1, with respect to electrical and
mechanical life time. The contact material is high quality
Beryllium-Copper (CuBe treated) with gold-plated surface.
The high current jacks are joint separately to the
connectors. To install them, carefully follow the assembly
instructions. It is extremely important to solder cables,
screw cable terminals or heat shrink sleeves to high current
jacks first, before inserting them into the moulding.
Paralleled converters should preferably be interconnected
on current bars or at a star point.
Using screw versions, the two outer high current jacks may
be inserted at a 90° angle in order to prevent possible short
circuits between the cable terminals, especially in
applications with high vibration environment. Heat shrink
sleeves might be necessary for further isolation purposes
or to keep clearances and creepage distances at specified
levels.
An extraction tool allows removal of the high current jacks
for replacement (see fig. 15).
Caution: The use of an adequate cable strain relief device (e.g.
Cable Hood etc.) is essential, in order to protect the high current
contact jacks from damage. Never screw, solder or manipulate
these contacts when the connector is plugged into the male
connector! The use of highly flexible cables is strongly
recommended.
This connector type (male version) is used in the following
converter series (case size): PSK and PSS (K01), K (K02),
P (Q04) with output currents ≥20 A.
Table 3: H15S2 and H15S4 Connector Survey
Female connector
type
Reference Description of terminals
STV-H15 S2-FSF/CO HZZ 00116 11 faston terminals 6.3 × 0.8 mm, 2 screw jacks ¹
STV-H15 S2-F/CO
HZZ 00115 11 faston terminals 6.3 × 0.8 mm, 2 solder jacks ¹
STV-H15 S4-FSF/CO HZZ 00110 7 faston terminals 6.3 × 0.8 mm, 4 screw jacks ¹
STV-H15 S4-F/CO
HZZ 00105 7 faston terminals 6.3 × 0.8 mm, 4 solder jacks ¹
STV-H15 S4-FLS/CO ² HZZ 00109 7 screw terminals 90°, 2.5 mm², torque ≤ 26.6 Ncm, 4 solder jacks ¹
STV-H15 S4-FSR/CO ² HZZ 00108 7 screw terminals, 90°, 2.5 mm², torque ≤ 26.6 Ncm, 4 screw jacks ¹
1 _{Spare jacks are available on request: screw version YVM002, solder version XMB045.}
2 _{Not for new designs. Use female connectors with faston terminals instead.}
Fig. Integrated
coding
10
yes
(10)
yes
12
yes
(12)
yes
13
yes
(13)
yes
Delivery content: H15S2 (S4) moulding, two (four) high current jacks and assembly instructions. Screw versions also
include four M4 screws with washers and heat shrink sleeves.
Mechanical Dimensions (in mm)
95
90
32 28 24 20 16 12
12054
European
Projection
30 26 22 18 14
84.9
8/10 4/6
13
Fig. 10
STV-H15 S2-FSF/CO
11 faston terminals and two screw jacks.
STV-H15 S2-F/CO
11 faston terminals and two solder jacks (solder jacks are shown in fig. 13).
SEP 29, 2003 revised to MAY 24, 2006
Page 5 of 9
www.power-one.com