FNP1500_10 Datasheet, PDF (4/17 Pages) Power-One – Front-Ends & FNR-3 Power Shelves Data Sheet

FNP1500/1800 Front-Ends
& FNR-3 Power Shelves Data Sheet
Output Specifications, 12Vout Models
Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated.
Parameter
Nominal output voltage
Output voltage set point accuracy
Output voltage trimming
Conditions/Description
I_o = 64.5 A
V_i = 230 VAC, I_o1 = 65.5 A, T_C = 25 °C
(Factory setting)
Adjustable via I²C (V_{o1 set})
Adjustable via Margin pin (R input)
Min
11.93
-0.42
7
6.2
Nominal
current
output 1
Nominal
current
output 1
Current
limit
output 1
Current
limit
output 1
FNP1500-12G
FNP1800-12G
FNP1500-12G
FNP1800-12G
Nominal current output 2
Current limit output 2
Static line regulation output 1
Static load
regulation
output 1
(droop
characteristic)
FNP1500-12G
Static load
regulation
output 1
(droop
characteristic)
FNP1800-12G
Static load regulation
output 2 (droop characteristic)
Dynamic
load
regulation
Current
Share
Start-up time
FNP1500-12G
& FNP1800-12G
FNP1500-12G
& FNP1800-12G
FNP1500-12G
FNP1800-12G
Output voltage ripple and noise
(Filter 10nF/10µF)
Remote sense
1 _{FNP1800-12G max is 12V.}
I_{o1 nom} @ V_i =108 VAC – 264 VAC, P_o 1.5 kW
I_{o1 nom} @ V_i = 85 VAC – 105 VAC, P_o 1.2 kW
I_{o1 nom} @ V_i =108 VAC – 264 VAC, P_o 1.75 kW
I_{o1 nom} @ V_i =108 VAC – 180 VAC, P_o 1.5 kW
I_{o1 nom} @ V_i = 85 VAC – 105 VAC, P_o 1.2 kW
I_{o1 max} @ V_i = 108 VAC – 264 VAC droop hiccup
I_{o1 max} @ V_i = 85 VAC – 105 VAC droop hiccup
I_{o1 max} @ V_i = 180 VAC – 264 VAC high droop
I_{o1 lim} @ V_i = 180 VAC – 264 VAC hiccup
I_{o1 max} @ V_i = 108 VAC – 180 VAC high droop
I_{o1 lim} @ V_i = 108 VAC – 180 VAC hiccup
I_{o1 max} @ V_i = 85 VAC – 105 VAC high droop
I_{o1 lim} @ V_i = 85 VAC – 105 VAC hiccup
I_{o2 nom} @ Vi = 85 VAC – 265 VAC, P_o 12 W
I_{o2 max} @ V_i = 85 VAC – 265 VAC
V_{i min} - V_{i max}, 50 % I_{o nom}, Ta = 25 °C
V_i = 230 V, 5 - 100 % I_{o nom}
Full load to no load [0..129 A] at V_o set = 12V
dV_o1 over the setting range [7 to 13V]
V_i = 230 V, 5 - 100 % I_{o nom}
Full load to no load [0..150 A] at V_o set = 12V
dV_o1 over the setting range [7 to 13V]
-0.5
11.64
-0.36
11.52
-0.48
Full load to no load @ Vi = 85 VAC – 265 VAC
Load change 50% <─>100% I_{o nom}, dI_o/dt =1A/s
Voltage deviation (droop + over- or undershoot)
-2
Max. recovery time to within 1% of V_{o1 nom}
Difference in current between two units for V_o1 above
10 % load.
Time required for output within regulation after initial
application of AC-input (V_{i nom}, I_{o nom})
after removal of inhibit (V_{i nom}, I_{o nom})
V_{i nom}, I_{o nom,} 20 MHz bandwidth
V_o1
V_o2
Total compensation for cable losses
Nom
12
12
12
129.0
101.8
150.0
129.0
101.8
147.4
120.2
156.4
168.4
135.4
147.4
108.2
120.2
1.0
1.5
- 5.58
12
- 5.58
12
0.4
12.9
15
100
Max
12.05
+0.42
13 ¹
V_{o1 set}
129.0
Units
VDC
VDC
% V_{o1 nom}
VDC
VDC
ADC
ADC
150.0
ADC
ADC
ADC
ADC
ADC
1.0
0.5
12.36
+0.36
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
% V_{o nom}
mV/A
VDC
VDC
12.36
+0.36
mV/A
VDC
VDC
VDC
2
% V_{o nom}
400
s
ADC
ADC
1.5
s
ms
120
mV_pp
120
mV_pp
500
mV
MCD10074 Rev. 1.2, 15-Apr-10
Page 4 of 17
www.power-one.com