ZY7015 Datasheet, PDF (3/34 Pages) Power-One – 3V to 13.2V Input 0.5V to 5.5V Output

ZY7015 15A DC-DC Intelligent POL Data Sheet
3V to 13.2V Input • 0.5V to 5.5V Output
4. Electrical Specifications
Specifications apply at the input voltage from 3V to 13.2V, output load from 0 to 15A, ambient temperature from -40°C to 85°C,
100µF output capacitance, and default performance parameters settings unless otherwise noted.
4.1 Input Specifications
Parameter
Input voltage (V_IN)
Conditions/Description
Min
At V_IN<4.75V, VLDO pin needs to be
connected to an external voltage source
3
higher than 4.75V
Input Current (at no load)
V_IN≥4.75V, VLDO pin connected to VIN
Undervoltage Lockout (VLDO
connected to VIN)
Ramping Up
Ramping Down
Undervoltage Lockout (VLDO
connected to V_AUX=5V)
Ramping Up
Ramping Down
External Low Voltage Supply
Connect to VLDO pin when V_IN<4.75V
4.75
VLDO Input Current
Current drawn from the external low
voltage supply at V_LDO=5V
Nom
50
4.2
3.75
3.0
2.5
50
Max
Units
13.2
VDC
mADC
VDC
VDC
VDC
VDC
13.2
VDC
mADC
4.2 Output Specifications
Parameter
Output Voltage Range (V_OUT)
Output Voltage Setpoint Accuracy
Output Current (I_OUT)
Line Regulation
Load Regulation
Dynamic Regulation
Peak Deviation
Settling Time
Conditions/Description
Programmable¹
Default (no programming)
V_IN=12V, I_OUT=0.5*I_{OUT MAX},
F_SW=500kHz, room temperature
V_{IN MIN} to V_{IN MAX}
V_{IN MIN} to V_{IN MAX}
0 to I_{OUT MAX}
Slew rate 2.5A/µs, 50 - 100% load step
C_OUT=300µF, F_SW=1MHz
to 10% of peak deviation
Output Voltage Peak-to-Peak
Ripple and Noise
BW=20MHz
Full Load
V_IN=5.0V, V_OUT=0.5V
V_IN=5.0V, V_OUT=2.5V
V_IN=13.2V, V_OUT=0.5V
V_IN=13.2V, V_OUT=2.5V
V_IN=13.2V, V_OUT=5.0V
Temperature Coefficient
Switching Frequency
Duty Cycle Limit
V_IN=12V, I_OUT=0.5*I_{OUT MAX}
Default
Programmable, 250kHz steps
Default
Programmable, 1.56% steps
Min
Nom
Max
0.5
5.5
0.5
(See Ordering Information)
-15²
15
±0.3
±0.3
100
50
10
15
15
25
35
20
500
500
1,000
90.5
0
95
Units
VDC
VDC
ADC
%V_OUT
%V_OUT
mV
µs
mV
mV
mV
mV
mV
mV
ppm/°C
kHz
kHz
%
%
1 _{ZY7015 is a step-down converter, thus the output voltage is always lower than the input voltage as show in Figure 1.}
2 _{At the negative output current (bus terminator mode) efficiency of the ZY7015 degrades resulting in increased internal power dissipation.}
Therefore maximum allowable negative current under specific conditions is 20% lower than the current determined from the derating curves
shown in paragraph 5.5.
ZD-00283 REV. 2.2
www.power-one.com
Page 3 of 34