PDIUSBP11 Datasheet, PDF (4/10 Pages) NXP Semiconductors – Universal Serial Bus transceiver

Philips Semiconductors
Universal Serial Bus transceiver
Preliminary specification
PDIUSBP11
DC ELECTRICAL CHARACTERISTICS
Over recommended operating conditions
Voltages are referenced to GND (ground = 0V)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = 0°C to +70°C
MIN TYP¹ MAX
V_IH
HIGH level input
V_CC = 3.0V to 3.6V³
2.0
V_IL
LOW level input
V_CC = 3.0V to 3.6V³
R_D H
Output impedance (HIGH state)
Note 2
28
R_D L
Output impedance (LOW state)
Note 2
28
V_CC = 3.0V; I_O = 6mA
2.2
V_OH
HIGH level output³
V_CC = 3.0V; I_O = 4mA
2.4
V_CC = 3.0V; I_O = 100µA
2.8
V_OL
LOW level output³
V_CC = 3.0V; I_O = 6mA
V_CC = 3.0V; I_O = 4mA
V_CC = 3.0V; I_O = 100µA
I_CCQ
Quiescent supply current
V_CC = 3.6V; V_I = V_CC or GND; I_O = 0
I_CCS
Supply current in Suspend
V_CC = 3.6V; V_I = V_CC or GND; I_O = 0
I_CCFS
Active supply current (Full Speed)
V_CC = 3.3V
I_CCLS Active supply current (Low Speed) V_CC = 3.3V
I_I
Input leakage current
V_CC = 3.6V; V_I = 5.5V or GND; not for I/O pins
I_OZ
3-State output OFF-state current
V_I = V_IH or V_IL; V_O = V_CC or GND ²
NOTES:
1. All typical values are at V_CC = 3.3V and T_amb = 25°C.
2. This value includes an external resistor of 24Ω "1%. See “Load D+ and D–” diagram for testing details.
3. All signals except D+ and D–.
0.8
34
43
35
51
2.7
–
0.3
–
330
–
10
2
"0.1
0.8
0.5
0.2
600
65
30
25
"5
"10
UNIT
V
V
Ω
Ω
V
V
µA
µA
mA
mA
µA
µA
AC CHARACTERISTICS
GND = 0V, t_R = t_F = 3.0ns, C_L = 50pF, R_L = 500Ω, V_CC = 3.3V
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
WAVEFORMS
T_amb = 25°C
T_amb = 0°C to +70°C UNIT
MIN TYP MAX MIN
MAX
tp_{LH VMO/VPO to D+/D–}
tp_HL ^{Full Speed}
t_rise
Rise and Fall Times
t_fall
Full Speed
tp_{LH VMO/VPO to D+/D–}
tp_HL ^{Low Speed}
t_rise
Rise and Fall Times
t_fall
Low Speed
tp_LH
D+/D– to RCV
tp_HL
tp_LH
D+/D– to VP/VM
tp_HL
tp_HZ
tp_{ZH OE# to D+/D–}
tp_LZ
RL = 500Ω
tp_ZL
0
1
0
4
2
4
30
1
30
75
2
75
3
1
4
12
0
12
0
20
4
20
4
300
30
300
30
300
75
200
75
16
16
8
8
12
12
10
10
15
ns
15
20
ns
20
300
ns
300
300
ns
200
16
ns
20
8
ns
12
12
15
ns
10
15
t_su
Setup for SPEED
5
0
ns
V_cr
Crossover point
Note 1
3
1.3
2.0
1.3
2.0
V
NOTE:
1. The crossover point is in the range of 1.3V to 2.5V for the low speed mode with a 50pF capacitance. In the low-speed mode with a 100pF or
greater capacitance, the crossover point is in the range of 1.3V to 2.0V.
1997 Sep 16
4