XA-G3 Datasheet, PDF (22/36 Pages) NXP Semiconductors – XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs

Philips Semiconductors
XA 16-bit microcontroller family
32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Product specification
XA-G3
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Operating temperature under bias
Storage temperature range
Voltage on EA/V_PP pin to V_SS
Voltage on any other pin to V_SS
Maximum I_OL per I/O pin
Power dissipation (based on package heat transfer limitations, not device power consumption)
RATING
–55 to +125
–65 to +150
0 to +13.0
–0.5 to V_DD+0.5V
15
1.5
UNIT
°C
°C
V
V
mA
W
DC ELECTRICAL CHARACTERISTICS
V_DD = 2.7V to 5.5V unless otherwise specified; V_DD = T_amb = 0 to +70°C for commercial, –40°C to +85°C for industrial, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
MIN
TYP
MAX
UNIT
Supplies
I_DD
I_ID
I_PD
I_PDI
V_RAM
V_IL
V_IH
Supply current operating
Idle mode supply current
Power-down current
Power-down current (–40°C to +85°C)
RAM-keep-alive voltage
Input low voltage
Input high voltage, except XTAL1, RST
30 MHz
30 MHz
RAM-keep-alive voltage
1.5
–0.5
At 5.0V
2.2
At 3.3V
2
60
80
mA
22
30
mA
5
100
mA
150
mA
V
0.22V_DD
V
V
V
V_IH1
Input high voltage to XTAL1, RST
For both 3.0 & 5.0V
0.7V_DD
V
V_OL
Output low voltage all ports, ALE, PSEN³
I_OL = 3.2mA, V_DD = 5.0V
1.0mA, V_DD = 3.0V
0.5
V
0.4
V
V_OH1
Output high voltage all ports, ALE, PSEN¹
I_OH = –100mA, V_DD = 4.5V
2.4
I_OH = –15mA, V_DD = 2.7V
2.0
V
V
V_OH2
Output high voltage, ports P0–3, ALE, PSEN²
I_OH = 3.2mA, V_DD = 4.5V
2.4
I_OH = 1mA, V_DD = 2.7V
2.2
V
V
C_IO
Input/Output pin capacitance
15
pF
I_IL
Logical 0 input current, P0–3⁶
V_IN = 0.45V
–25
–75
mA
I_LI
Input leakage current, P0–3⁵
V_IN = V_IL or V_IH
±10
mA
I_TL
Logical 1 to 0 transition current all ports⁴
At 5.5V
–650
mA
NOTES:
1. Ports in Quasi bi-directional mode with weak pull-up (applies to ALE, PSEN only during RESET).
2. Ports in Push-Pull mode, both pull-up and pull-down assumed to be same strength
3. In all output modes
4. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when
V_IN is approximately 2V.
5. Measured with port in high impedance output mode.
6. Measured with port in quasi-bidirectional output mode.
7. Load capacitance for all outputs=80pF.
8. Under steady state (non-transient) conditions, I_OL must be externally limited as follows:
Maximum I_OL per port pin:
15mA (*NOTE: This is 85°C specification for V_DD = 5V.)
Maximum I_OL per 8-bit port:
26mA
Maximum total I_OL for all output: 71mA
If I_OL exceeds the test condition, V_OL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
9. See Figures 25, 26, 29, and 30 for I_DD test conditions, and Figures 27 and 28 for I_CC vs. Frequency.
Max. 5V Active I_DD = (fosc * 1.77 mA) + 7 mA
Max. 5V Idle I_DD = (fosc * 0.87 mA) + 4 mA
Max. 3V Active I_DD = (fosc * 0.77 mA) + 7 mA
Max. 3V Idle I_DD = (fosc * 0.54 mA) + 4 mA
1999 Apr 07
22