|
TDA8008 Datasheet, PDF (2/12 Pages) NXP Semiconductors – Dual multiprotocol smart card coupler | |||
|
◁ |
Philips Semiconductors
Dual multiprotocol smart card coupler
Objective speciï¬cation
TDA8008
FEATURES
⢠8xC51 core with 16 kbytes or EPROM (TDA8008),
256 bytes RAM, 512 bytes AUXRAM, Timer 0, 1, 2 and
enhanced UART
⢠Specific ISO 7816 UART, accessible with MOVX
instructions for automatic convention processing,
variable baud rate through frequency or division ratio
programming, error management at character level for
T = 0 protocol, extra guard time register
⢠Dual VCC generation (5 V ±5% or 3 V ±5%), maximum
current of 60 mA with controlled rise and fall times
⢠Dual cards clock generation (up to 10 MHz) with two
times synchronous frequency doubling
⢠Cards clock STOP HIGH or LOW or 1.25 MHz (from an
integrated oscillator) for cards power reduction mode
⢠Automatic activation and deactivation sequences
through an independent sequencer
⢠Supports the asynchronous protocols T = 0 and T = 1 in
accordance with ISO 7816 and EMV
⢠Versatile 24-bit time-out counter for Answer To Reset
(ATR) and waiting times processing
⢠22 ETU counter for block guard time
⢠Supports synchronous cards
⢠Current limitations on cards contacts
⢠Special circuitry for killing spikes during power-on or off
⢠Supply supervisor for Power-on reset
⢠Step-up converter (supply voltage from 2.7 to 5.5 V at
16 MHz), doubler, tripler or follower according to VCC
and VDD
⢠Speed up to 25 MHz at VDD = 5 V
⢠Additional I/O pin allowing the use of the ISO 7816
UART for an external card interface (pin IOAUX)
⢠Additional interrupt pin allowing detection of level
toggling on an external signal (pin INTAUX)
⢠Fast and efficient swapping between the 3 cards due to
separate buffering of parameters for each card
⢠Chip select input allowing use of several devices in
parallel and memory space paging
⢠Enhanced ESD protections on card contacts (6 kV min.)
⢠Software library for easy integration within the
application
⢠Development tool with a TDA8007B and a regular
emulator.
APPLICATIONS
⢠Multiple smart card readers for multiprotocol
applications (EMV banking, digital pay TV, access
control, etc.).
GENERAL DESCRIPTION
The TDA8008 is a complete, one-chip, low cost dual smart
card coupler.
It can be used as the kernel of a multiple card reader. It can
handle all ISO 7816, EMV and GSM11-11 requirements.
The integrated ISO 7816 UART and the time-out counters
allow easy use even at high baud rates with no real time
constraints. Due to its chip select and external I/O and
interrupt features, it simplifies the realization of any
number of cards reader. It gives the cards and the set a
very high level of security, due to its special hardware
against ESD, short-circuiting, power failure and
overheating. Its integrated step-up converter allows
operation within a supply voltage range of 2.7 to 5.5 V at
16 MHz.
The OTP version of the TDA8008 allows fast and reliable
software development and fast product introduction.
A software library has been developed, that can handle all
actions required for T = 0, T = 1 and synchronous
protocols.
ORDERING INFORMATION
TYPE NUMBER
TDA8008HL
NAME
LQFP80
PACKAGE
DESCRIPTION
plastic low proï¬le quad ï¬at package; 80 leads; body 12 à 12 à 1.4 mm
VERSION
SOT315-1
1999 Dec 14
2
|
▷ |