TDA6500 Datasheet, PDF (16/37 Pages) NXP Semiconductors – 5 V mixer/oscillator and synthesizer for PAL and NTSC standards

Philips Semiconductors
TDA6500; TDA6501
5 V mixer/oscillator and synthesizer for PAL and NTSC standards
11. Characteristics
Table 18: Supplies
V_CC = 5 V; T_amb = 25 °C; values are given for an IF amplifier with 500 Ω load (measured as shown in Figure 7 for the PAL
standard); unless otherwise specified.
Symbol Parameter
Conditions
Min Typ Max Unit
Supply
V_CC
supply voltage
I_CC
supply current
all PNP ports off
one PNP port on; sourcing 20 mA
4.5 5.0 5.5 V
-
74
94
mA
-
96
116 mA
two PNP ports on; one port sourcing
20 mA; one other port sourcing 5 mA
102 122 mA
Table 19: PLL
V_CC = 5 V; T_amb = 25 °C; values are given for an IF amplifier with 500 Ω load (measured as shown in Figure 7 for the PAL
standard); unless otherwise specified.
Symbol Parameter
Conditions
Min Typ Max Unit
Functional range
V_POR
power-on reset supply
voltage
for a voltage lower than V_POR,
power-on reset is active
1.5 3.5 -
V
N
divider ratio
15-bit frequency word
64
-
32 767
f_XTAL
Z_XTAL
crystal oscillator frequency R_XTAL = 25 Ω to 300 Ω
input impedance (absolute f_XTAL = 4 MHz
value)
3.2 4.0 4.48 MHz
600 1200 -
Ω
PMOS ports: P0, P1, P2 and P3
I_LO
output leakage current
V_DS(P0)(sat) output saturation voltage
V_DS(P1)(sat) output saturation voltage
V_DS(P2)(sat), output saturation voltage
V_DS(P3)(sat)
NPN ports: P4 and P6
V_CC = 5.5 V; V_Pn = 0 V
buffer P0 is on only; sourcing 10 mA
buffer P1 is on only; sourcing 20 mA
buffer P2 or P3 is on; sourcing 5 mA
-
-
10
µA
-
0.25 0.4 V
-
0.25 0.4 V
-
0.25 0.4 V
I_LO
V_CE(sat)
ADC input
output leakage current
output saturation voltage
V_CC = 5.5 V; V_Pn = 6 V
buffer P4 or P6 is on; sinking 5 mA
-
-
10
µA
-
0.25 0.4 V
V_I
ADC input voltage
I_IH
HIGH-level input current
I_IL
LOW-level input current
AS input (address selection)
see Table 13
ADC input V_i = V_CC
ADC input V_i = 0 V
0
-
-
-
−10 -
V_CC
V
10
µA
-
µA
I_IH
HIGH-level input current
I_IL
LOW-level input current
SCL and SDA inputs
AS input V_i = V_CC
AS input V_i = 0 V
-
-
−10 -
10
µA
-
µA
V_IL
LOW-level input voltage
V_IH
HIGH-level input voltage
I_IH
HIGH-level input current V_BUS = 5.5 V; V_CC = 0 V
V_BUS = 5.5 V; V_CC = 5.5 V
0
-
2.3 -
-
-
-
-
1.5 V
5.5 V
10
µA
10
µA
9397 750 15057
Product data sheet
Rev. 02 — 14 June 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
16 of 37