PI3HDMI101ZHEX Datasheet, PDF (8/14 Pages) Pericom Semiconductor Corporation – 1:1 Active HDMI™ ReDriver™ with Optimized Equalization & I2C Buffer

ADVANCE INFORMATION - COMPANY CONFIDENTIAL
PI3HDMI101
1:1 Active HDMI^TM Redriver with
Optimized Equalization & I²C Buffer
Electrical Characteristics (over recommended operating conditions unless otherwise noted)
Symbol
Parameter
Test Conditions
Min. Typ.⁽¹⁾ Max. Units
I_DD Supply Current
P_D
Power Dissipation
V_IH = V_DD, V_IL = V_DD - 0.4V,
R_T = 50-ohm, V_DD = 3.3V
Data Inputs = 1.65 Gbps HDMI
data pattern
CLK Inputs = 165 MHz clock
OC_Sx = Low, x = 0,1,2,3
120
mA
400
mW
I_DDQ Standby Current
OE = HIGH, VDD = 3.3V, Source
= off
2
mA
TMDS Differential Pins
V_OH Single-ended high-level output voltage
V_DD-
10
V_DD
+ 10
V_OL Single-ended low-level output voltage
V_swing
V_OD(O)
V_OD(U)
ΔV_OC(SS)
Single-ended output swing voltage
Overshoot of output differential voltage
Undershoot of output differential voltage
Change in steady-state common-mode
output voltage between logic states
V_DD = 3.3V, R_T = 50-ohm
Pre-emphasis/De-emphasis = 0dB
V_DD
- 600
V_DD mV
- 400
400
600
6% 15% _2x
12% 25% ^Vswing
0.5
5
mV
I_(OS) Short circuit output current
V_ODE(SS) Steady state output differential voltage
OC_Sx = GND, Data Inputs = 250 560
Mbps HDMI data pattern,
V_ODE(PP) Peak-to-peak output differential voltage _{25 MHz pixel clock, x = 0,1,2,3}
800
12
840
1200
mA
mVp-p
V_I(open)
Single-ended input voltage under high
impedance input or open input
I_I = 10μA
V_DD
- 10
V_DD +
10
mV
R_INT Input termination resistance
Control Pins (OE, DDC_EN, IADJ)
V_IN = 2.9V, RxSense pin = HIGH
45 50 55 ohm
I_IH High-level digital input current
I_IL Low-level digital input current
I²C Pins (SCL_T, SDA_T) (T Port)
V_IH = 2V or V_DD
V_I = GND or 0.8 V
-10
10
μA
-10
10
I_ikg Input leakage current
I_OH High-level output current
V_I = 5.5 V
V_I = V_DD
V_O = 3.6 V
-50
50
-20
20
μA
-10
10
I_IL Low-level input current
V_OL Low-level output voltage
V_IL = GND
I_OL = 2.5 mA
IADJ = H
-40
40
0.65
0.9
V
C_IO¹ Input/output capacitance
V_DD = 0V or 3.0V, Frequency =
100kHz
4
7
pF
V_OH(TTL)² TTL High-level output voltage
V_OL(TTL) ² TTL Low-level output voltage
Note:
1. Measured at Vbias = 0V or 5V, Vrms = 0.2V;
Vbias = 1.65V, Vrms = 0.84V;
Vbias = 2.5V, Vrms = 1.2V.
2. Voh/Vol of external driver at the R and T ports.
I_OH = -8 mA
I_OL = 8 mA
(Table Continued)
2.4
V
0.4
All trademark⁰s⁹a^-r⁰e⁰p⁵ro⁵perty of their respective owners.
8
PS8924C
10/05/09