PI3WVR12612 Datasheet, PDF (5/13 Pages) Pericom Semiconductor Corporation – HDMI 2.0, DisplayPort 1.2 Video Switch

PI3W VR12612
HDMI 2.0, DisplayPort 1.2 Video Switch
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ........................................................... –65°C to +150°C
Supply Voltage to Ground Potential ....................................–0.5V to +4.2V
DC Input Voltage .......................................................................–0.5V to V_DD
High Speed Data Channel........................................................ –0.5V to 3.8V
HPD_x, SDA_x, SCL_x............................................................. -0.5V to 5.5V
DC Output Current ..............................................................................120mA
Power Dissipation .................................................................................... 0.5W
Note: Stresses greater than those listed under MAXI-
MUM RATINGS may cause permanent damage to
the device. This is a stress rating only and functional
operation of the device at these or any other conditions above
those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect reliability.
DC Electrical
3.3V ±10%)
Characteristics
for
Switching
over
Operating
Range
(T_A
=
–40°C
to
+105°C,
V_DD
=
Parameter Description
Test Conditions⁽¹⁾
Min Typ⁽²⁾ Max Units
VIH
VIL
VIH
VIM
VIL
VIK
VIK
IIH
IIL
I_{OFF_SB}
R_{ON_HS}
R_{ON_AUX}
R_{ON_DDC}
R_{ON_HPD}
V_{AUX_SS}
V_{HPD_I}
V_{HPD_O}
V_{SDA_X}
V_PASS
(SDA_X)
V_{SCL_X}
Input HIGH Voltage (OE, GPU_SEL)
Input LOW Voltage (OE, GPU_SEL)
Input HIGH Voltage (DDC_AUX_SEL)
Input Mid-Level Voltage (DDC_AUX_
SEL)
Input LOW Voltage (DDC_AUX_SEL)
Clamp Diode Voltage (HS Channel)
Clamp Diode Voltage (Aux, Cntrl )
Input HIGH Current (All Control Pins)
Input LOW Current (All Control Pins)
I/O leakage when part is off for sideband
signals only (DDC, AUX, HPD)
On resistance between input to output for
high speed signals
On resistance between input to output for
side-band signals (AUX)
On resistance between input to output for
DDC channel
On resistance between input to output for
HPD channel
Signal Swing Tolerance in Aux path
Input voltage on HPD path
Output voltage tolerance on HPD path
Input Voltage on SDA path
Switch output voltage tolerance input
Input Voltage on SCL path
Guaranteed HIGH level
1.5
Guaranteed LOW level
Guaranteed HIGH level
2.65
Guaranteed MID level
V_DD/2-
300mV
Guaranteed LOW level
-0.5
V_DD = Max., I_IN = –18mA
V_DD = Max., I_IN = –18mA
V_DD = Max., V_IN = V_DD
V_DD = Max., V_IN = GND
V_DD = 0V, V_INPUT = 0V to
3.6V
V_INPUT,cm = 0V to 3.4V,
V_INPUT,diff < 1.2V_p-p,diff,
V_DD = 3.0V, I_INPUT = 20mA
V_DD = 3.0V, Vinput = 0 to 3.3V,
I_INPUT = 20mA
V_DD = 3.0V, Vinput = 0V,
I_INPUT = 20mA
V_DD = 3.0V, Vinput = 0 to 3.0V,
I_INPUT = 20mA
V_DD = 3.0V
–0.5
HPD input from 3.3V to 5.25V
V_in = 5.25V, Ii = 100uA, V_DD
= 3.3V
1.8
V_DD/2
–1.6V
–0.7
11
7
12
7
3.3
5
2.2
5
0.75
V_DD
V_DD/2+
300mV
0.6
–1.8
–1.5
±5
±5
20
5.5
5.5
3.6
2.5
V
µA
Ohm
Ohm
Ohm
Ohm
V
V
V
V
V
V
V_PASS
(SCL_X)
Switch output voltage tolerance input
V_in = 5.25V, Ii = 100uA, V_DD
= 3.3V
1.8
2.2
2.5
V
All trademarks are property of their respective owners.
15-0175
5
www.pericom.com 12/03/15