English
Language : 

PI3V713-A Datasheet, PDF (4/8 Pages) Pericom Semiconductor Corporation – 3.3V, 7-Channel Analog Video Switch
◁
PI3V713-A
3.3V, 7-Channel Analog Video Switch
Capacitance (TA = 25°C, f = 1MHz)
Parameters(4)
Description
Test Conditions(1)
Typ.(2)
Units
CIN
Input Capacitance
2.0
COFF
RGB Capacitance, Switch OFF
2.4
pF
CON
RGB Switch Capacitance, Switch ON
5.6
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VDD = 3.3V, Ta = 25°C ambient and maximum loading.
3. Measured by the voltage drop between input and output pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages
on the two pins.
4. This parameter is determined by device characterization but is not production tested.
Power Supply Characteristics
Parameters
Description
Test Conditions(1)
Min.
ICC _3.3V rail
Quiescent PowerSupply
Current for 3.3V power rail
VDD = Max., VDD = 3.6V, 5V VDD = 5.5V
VSEL = GND or VDD
-
ICC_5V VDD
Quiescent Power supply
current for 5V VDD
5V VDD = 5.5V, VDD = 3.6V,
VSEL= GND or VDD
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VDD = 3.3V, Ta = 25°C ambient and maximum loading.
Typ.(2)
250
100
Max.
500
500
Units
µA
nA
Dynamic Electrical Characteristics Over the Operating Range (TA=-40º to +85ºC, VDD=3.3V±10%, GND=0V)
Parameters
Description
Test Conditions
Min. Typ.(2) Max. Units
XTALK
OIRR
BW
Crosstalk
OFF Isolation
Bandwidth –3dB
f = 250MHz, See Fig. 2
f = 250MHz, See Fig. 3
See Fig. 1
-
-38
-
dB
-
-46
-
-
1.7
-
GHz
Freq = 10MHz (VGA)
-1.77
ILOSS
Insertion Loss for RGB
path
with 75-Ohm
load
Freq = 100MHz (XGA)
-1.88
dB
Freq = 300MHz (UXGA)
-2.09
Switching Characteristics
Parameters
tPD
Propagation Delay(2,3)
Description
tPZH, tPZL
Line Enable Time - SEL to Input, Output
tPHZ, tPLZ
Line Disable Time - SEL to Input, Output
tSK(p)
Trise (H/V)
Skew between opposite transitions of the same output
(tPHL - tPLH) (2)
Horizontal/Vertical synchronous output rise time (H1_out, V1_out,
H2_out, and V2_out) with 15pF load
Min.
-
0.5
0.5
-
Typ.(2)
0.25
-
-
0.1
Max.
15
10
0.2
1.5
Units
ns
Horizontal/Vertical synchronous output fall time (H1_out, V1_out,
Tfall (H/V)
H2_out, and V2_out) with 15pF load
1.6
Notes:
1. For max. or min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Guaranteed by design.
3. The switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The time constant for the
switch alone is of the order of 0.25ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little
propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the
switch and its interactions with the load on the driven side.
10-0192
4
PS9101
06/29/10
 ▷