PI29FCT520T Datasheet, PDF (3/5 Pages) Pericom Semiconductor Corporation – FAST CMOS MULTILEVEL PIPELINE REGISTERS

PI29FCT520/521T/2520T
112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788^M990011^U2233^L44^T5566^I77^L8899^E0011^V2233^E44^L556677^P88^I99^P0011^E2211^L22^I3344^N55^E667788^R9900^E11^G2233^I44^S5566^T7788^E99^R0011^S2233
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................................................. –55°C to +125°C
Ambient Temperature with Power Applied ................................. -40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ....... –0.5V to +7.0V
DC Input Voltage ......................................................................... –0.5V to +7.0V
DC Output Current ................................................................................... 120 mA
Power Dissipation ......................................................................................... 0.5W
Note:
Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or any other conditions above those
indicated in the operational sections of this
specification is not implied. Exposure to
absolute maximum rating conditions for
extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ± 5%)
Parameters Description
Test Conditions⁽¹⁾
Min. Typ⁽²⁾
VOH
Output HIGH Voltage
VCC = MIN., VIN = VIH OR VIL IOH = –15.0 mA
2.4
3.0
IOL = 48 mA
0.3
VOL
Output LOW Voltage
VCC = MIN., VIN = VIH OR VIL
IOL = 12 mA (25Ω series)
0.3
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
IIH
Input HIGH Current
Guaranteed Logic LOW Level
VCC = MAX.
VIN = VCC
IIL
Input LOW Current
VCC = MAX.
VIN = GND
IOZH
High Impedance
VCC = MAX.
VOUT = 2.7V
IOZL
Output Current
VIK
Clamp Diode Voltage
IOS
Short Circuit Current
VCC = MIN., IIN = –18 mA
VCC = MAX.⁽³⁾, VOUT = GND
VOUT = 0.5V
–0.7
–60 –120
IOFF
Power Down Disable
VH
Input Hysteresis
VCC = GND, VOUT = 4.5V
—
—
200
Max.
0.50
0.50
0.8
1
–1
1
–1
–1.2
100
Units
V
V
V
V
V
µA
µA
µA
µA
V
mA
µA
mV
Capacitance (TA = 25°C, f = 1 MHz)
Parameters⁽⁴⁾ Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
VIN = 0V
VOUT = 0V
Typ
Max.
Units
6
10
pF
8
12
pF
Notes:
1. For conditions show as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device
type.
2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. This parameter is determined by device characterization but is not production tested.
FCT520.pm6
3
3
12/18/96, 4:44 PM
PS2002B 12/10/96