CAT9555 Datasheet, PDF (4/18 Pages) Catalyst Semiconductor – 16-bit I2C and SMBus I/O Port with Interrupt

CAT9555
D.C. OPERATING CHARACTERISTICS
V_CC = 2.3V to 5.5V; V_SS = 0V; T_A = -40°C to +85°C, unless otherwise specified.
Symbol Parameter
Supplies
V_CC Supply voltage
I_CC Supply current
I_stbl Standby current
I_stbh Standby current
V_POR Power-on reset voltage
SCL, SDA, ¯IN¯T¯
V_IL(1)
V_IH ⁽¹⁾
Low level input voltage
High level input voltage
I_OL Low level output current
I_L
C_I ⁽²⁾
C_O ⁽²⁾
Leakage current
Input capacitance
Output capacitance
A0, A1, A2
V_IL(1)
V_IH(1)
Low level input voltage
High level input voltage
I_LI
Input leakage current
I/Os
Conditions
Min
2.3
Operating mode; VCC = 5.5V;
no load; fSCL = 100kHz
—
Standby mode; VCC = 5.5V; no load;
VI = VSS; fSCL = 0kHz; I/O = inputs
—
Standby mode; VCC = 5.5V; no load;
VI = VCC; fSCL = 0kHz; I/O = inputs
—
No load; V_I = V_CC or V_SS
—
V_OL = 0.4V
V_I = V_CC = V_SS
V_I = V_SS
V_O = V_SS
-0.5
0.7 x V_CC
3
1–
—
—
-0.5
0.7 x V_CC
-1
V_IL
V_IH
I_OL
V_OH
I_IH
I_IL
C_I ⁽²⁾
C_O ⁽²⁾
Low level input voltage
High level input voltage
Low level output current
High level output voltage
Input leakage current
Input leakage current
Input capacitance
Output capacitance
V_OL = 0.5V;
V_CC = 2..3V to 5.5V⁽³⁾
V_OL = 0.7V;
V_CC = 2.3V to 5.5V⁽³⁾
I_OH = -8 mA; V_CC = 2.3V⁽⁴⁾
I_OH = -10 mA; V_CC = 2.3V ⁽⁴⁾
I_OH = -8 mA; V_CC = 3.0V ⁽⁴⁾
I_OH = -10 mA; V_CC = 3.0V ⁽⁴⁾
I_OH = -8 mA; V_CC = 4.75V ⁽⁴⁾
I_OH = -10mA; V_CC = 4.75V ⁽⁴⁾
V_CC = 3.6V; V_I = V_CC
V_CC = 5.5V; V_I = V_SS
-0.5
0.7 x V_CC
8
10
1.8
1.7
2.6
2.5
4.1
4.0
—
—
—
—
Typ
—
135
1.1
0.75
1.5
—
—
—
—
—
—
—
—
—
—
—
8 to 20
10 to 24
—
—
—
—
—
—
—
—
—
—
Max
5.5
200
1.5
1
1.65
0.3 x V_CC
5.5
—
+1
6
8
0.3 x V_CC
5.5
1
0.3 x V_CC
5.5
—
—
—
—
—
—
—
—
1
-100
5
8
Unit
V
µA
mA
µA
V
V
V
mA
µA
pF
pF
V
V
µA
V
V
mA
mA
V
V
V
V
V
V
µA
µA
pF
pF
Notes:
(1) VIL min and VIH max are reference values only and are not tested.
(2) This parameter is characterized initially and after a design or process change that affects the parameter. Not 100% tested.
(3) Each I/Os must be externally limited to a maximum of 25mA and each octal (I/O0.0 to I/O0.7 and I/O1.0 to I/O1.7) must be limited to a
maximum current of 100mA for a device total of 200mA.
(4) The total current sourced by all I/Os must be limited to 160mA.
Doc. No. MD-9003 Rev. J
4
© 2010 SCILLC. All rights reserved
Characteristics subject to change without notice