MC74VHC1GT04_16 Datasheet, PDF (3/6 Pages) ON Semiconductor – Inverting Buffer / CMOS Logic Level Shifter

MC74VHC1GT04
DC ELECTRICAL CHARACTERISTICS
Symbol
V_IH
Parameter
Minimum High−Level
Input Voltage
Test Conditions
V_CC
T_A = 25°C
T_A ≤ 85°C −55 ≤ T_A ≤ 125°C
(V) Min Typ Max Min Max Min
Max _Unit
3.0 1.4
4.5 2.0
5.5 2.0
1.4
1.4
V
2.0
2.0
2.0
2.0
V_IL
Maximum Low−Level
Input Voltage
3.0
0.53
0.53
0.53
V
4.5
0.8
0.8
0.8
5.5
0.8
0.8
0.8
V_OH Minimum High−Level
Output Voltage
V_IN = V_IH or V_IL
V_OL Maximum Low−Level
Output Voltage
V_IN = V_IH or V_IL
I_IN
Maximum Input
Leakage Current
V_IN = V_IH or V_IL
I_OH = −50 mA
V_IN = V_IH or V_IL
I_OH = −4 mA
I_OH = −8 mA
V_IN = V_IH or V_IL
I_OL = 50 mA
V_IN = V_IH or V_IL
I_OL = 4.0 mA
I_OL = 8.0 mA
V_IN = 5.5 V or GND
3.0 2.9 3.0
2.9
2.9
V
4.5 4.4 4.5
4.4
4.4
3.0 2.58
4.5 3.94
V
2.48
2.34
3.80
3.66
3.0
0.0 0.1
0.1
4.5
0.0 0.1
0.1
0.1
V
0.1
V
3.0
0.36
0.44
0.52
4.5
0.36
0.44
0.52
0 to
±0.1
±1.0
±1.0
mA
5.5
I_CC Maximum Quiescent
V_IN = V_CC or GND
5.5
Supply Current
1.0
20
40
mA
I_CCT
Quiescent Supply
Current
Input: V_IN = 3.4 V
5.5
1.35
1.50
1.65 mA
I_OPD Output Leakage
V_OUT = 5.5 V
0.0
Current
0.5
5.0
10
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
AC ELECTRICAL CHARACTERISTICS C_load = 50 pF, Input t_r = t_f = 3.0 ns
T_A = 25°C
T_A ≤ 85°C −55 ≤ T_A ≤ 125°C
Symbol
Parameter
Test Conditions
Min Typ Max Min Max Min
Max _Unit
t_PLH, Maximum Propagation V_CC = 3.3 ± 0.3 V C_L = 15 pF
5.0 10.0
11.0
t_PHL Delay, Input A to Y
C_L = 50 pF
6.2 13.5
15.0
13.0
ns
17.5
V_CC = 5.0 ± 0.5 V C_L = 15 pF
3.8 6.7
7.5
8.5
C_L = 50 pF
4.2 7.7
8.5
9.5
C_IN Maximum Input
Capacitance
5.0 10
10
10
pF
Typical @ 25°C, V_CC = 5.0 V
C_PD Power Dissipation Capacitance (Note 5)
10
pF
5. C_PD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: I_CC(OPR) = C_PD  V_CC  f_in + I_CC. C_PD is used to determine the no−load dynamic
power consumption; P_D = C_PD  V_CC2  f_in + I_CC  V_CC.
www.onsemi.com
3