MC74HC4316A_14 Datasheet, PDF (3/10 Pages) ON Semiconductor – Quad Analog Switch/ Multiplexer/Demultiplexer

MC74HC4316A
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
V_CC Positive DC Supply Voltage
(Ref. to GND)
–0.5 to +7.0
V
(Ref. to V_EE) –0.5 to +14.0
V_EE Negative DC Supply Voltage (Ref. to GND)
–7.0 to +0.5
V
V_IS Analog Input Voltage
V_EE – 0.5
V
to V_CC + 0.5
V_in DC Input Voltage (Ref. to GND)
–0.5 to V_CC + 0.5 V
I
DC Current Into or Out of Any Pin
±25
mA
P_D Power Dissipation in Still Air
SOIC Package*
500
mW
T_stg Storage Temperature
– 65 to + 150
°C
T_L Lead Temperature, 1 mm from Case for 10 Seconds)
260
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
*Derating − SOIC Package: –7 mW/°C from 65° to 125°C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
I/O pins must be connected to a
properly terminated line or bus.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
V_CC Positive DC Supply Voltage (Ref. to GND)
2.0
6.0
V
V_EE Negative DC Supply Voltage (Ref. to GND)
–6.0
GND
V
V_IS Analog Input Voltage
V_EE
V_CC
V
V_in Digital Input Voltage (Ref. to GND)
GND
V_CC
V
V_IO* Static or Dynamic Voltage Across Switch
−
1.2
V
T_A Operating Temperature, All Package Types
–55
+125
°C
t_r, t_f Input Rise and Fall Time
(Control or Enable Inputs)
(Figure 10)
V_CC = 2.0 V
0
V_CC = 3.0 V
0
V_CC = 4.5 V
0
V_CC = 6.0 V
0
1000
ns
600
500
400
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
*For voltage drops across the switch greater than 1.2 V (switch on), excessive V_CC current may be drawn; i.e., the current out of the switch may
contain both V_CC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC ELECTRICAL CHARACTERISTICS Digital Section (Voltages Referenced to GND) V_EE = GND Except Where Noted
Guaranteed Limit
Symbol
Parameter
Test Conditions
V_CC –55 to
V
25°C
≤ 85°C ≤ 125°C Unit
V_IH Minimum High−Level Voltage, Control R_on = Per Spec
or Enable Inputs
2.0
1.5
1.5
1.5
V
3.0
2.1
2.1
2.1
4.5
3.15
3.15
3.15
6.0
4.2
4.2
4.2
V_IL Maximum Low−Level Voltage, Control R_on = Per Spec
or Enable Inputs
2.0
0.5
0.5
0.5
V
3.0
0.9
0.9
0.9
4.5
1.35
1.35
1.35
6.0
1.8
1.8
1.8
I_in
Maximum Input Leakage Current,
Control or Enable Inputs
I_CC Maximum Quiescent Supply Current
(per Package)
V_in = V_CC or GND
6.0
V_EE = –6.0 V
V_in = V_CC or GND
V_IO = 0 V
V_EE = GND 6.0
V_EE = –6.0 6.0
±0.1
2
4
±1.0
20
40
±1.0
mA
mA
40
160
http://onsemi.com
3