MC74HC165A_16 Datasheet, PDF (3/12 Pages) ON Semiconductor – 8-Bit Serial or Parallel-Input/ Serial-Output Shift Register

MC74HC165A
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
V_CC DC Supply Voltage (Referenced to GND)
– 0.5 to + 7.0
V
V_in DC Input Voltage (Referenced to GND)
– 0.5 to V_CC + 0.5 V
V_out DC Output Voltage (Referenced to GND)
– 0.5 to V_CC + 0.5 V
I_in
DC Input Current, per Pin
± 20
mA
I_out DC Output Current, per Pin
± 25
mA
I_CC DC Supply Current, V_CC and GND Pins
± 50
mA
P_D Power Dissipation in Still Air
Plastic DIP†
750
mW
SOIC Package†
500
TSSOP Package†
450
T_stg Storage Temperature
– 65 to + 150
_C
T_L Lead Temperature, 1 mm from Case for 10 Seconds
_C
(Plastic DIP, SOIC or TSSOP Package)
260
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
†Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C
SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: − 6.1 mW/_C from 65_ to 125_C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max Unit
V_CC
V_in, V_out
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to
GND)
2.0
6.0
V
0
V_CC
V
T_A Operating Temperature, All Package Types
– 55 + 125 _C
t_r, t_f Input Rise and Fall Time
(Figure 1)
V_CC = 2.0 V
0
V_CC = 3.0 V
0
V_CC = 4.5 V
0
V_CC = 6.0 V
1000 ns
600
500
400
Functional operation above the stresses listed in the Recommended Operating Ranges is not
implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may
affect device reliability.
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
Symbol
Parameter
V_CC
Test Conditions
V
V_IH Minimum High−Level Input V_out = 0.1 V or V_CC – 0.1 V
2.0
Voltage
|I_out| v 20 mA
3.0
4.5
6.0
V_IL Maximum Low−Level Input V_out = 0.1 V or V_CC – 0.1 V
2.0
Voltage
|I_out| v 20 mA
3.0
4.5
6.0
V_OH Minimum High−Level Output V_in = V_IH or V_IL
2.0
Voltage
|I_out| v 20 mA
4.5
6.0
V_in = V_IH or V_IL |I_out| v 2.4 mA 3.0
|I_out| v 4.0 mA 4.5
|I_out| v 5.2 mA 6.0
Guaranteed Limit
– 55 to 25_C v 85_C v 125_C
1.5
1.5
1.5
2.1
2.1
2.1
3.15
3.15
3.15
4.2
4.2
4.2
0.5
0.5
0.5
0.9
0.9
0.9
1.35
1.35
1.35
1.80
1.80
1.80
1.9
1.9
1.9
4.4
4.4
4.4
5.9
5.9
5.9
2.48
2.34
2.20
3.98
3.84
3.70
5.48
5.34
5.20
Unit
V
V
V
V
www.onsemi.com
3