|
LC87F0808AUQFPTLM-H Datasheet, PDF (2/25 Pages) ON Semiconductor – 8-bit 1-chip Microcontroller | |||
|
◁ |
LC87F0808A
ï®Ports
⢠Normal withstand voltage I/O ports
Ports I/O direction can be designated in 1-bit units
Ports I/O direction can be designated in 4-bit units
⢠Dedicated oscillator ports/input ports
⢠Reset pin
⢠On-chip Debugger pin
⢠Power pins
20 (P1n, P20, P21, P30 to P35, P70 to P73)
8 (P0n)
2 (CF1/XT1, CF2/XT2)
1 (RES)
1 (OWP0)
4 (VSS1, VSS2, VDD1, VDD2)
ï®Timers
⢠Timer 0: 16-bit timer/counter with a capture register.
Mode 0: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) Ã 2 channels
Mode 1: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register)
+ 8-bit counter (with an 8-bit capture register)
Mode 2: 16-bit timer with an 8-bit programmable prescaler (with a 16-bit capture register)
Mode 3: 16-bit counter (with a 16-bit capture register)
⢠Timer 1: 16-bit timer/counter that supports PWM/toggle outputs
Mode 0: 8-bit timer with an 8-bit prescaler (with toggle outputs) + 8-bit timer/
counter with an 8-bit prescaler (with toggle outputs)
Mode 1: 8-bit PWM with an 8-bit prescaler à 2 channels
Mode 2: 16-bit timer/counter with an 8-bit prescaler (with toggle outputs)
(toggle outputs also possible from the lower-order 8 bits)
Mode 3: 16-bit timer with an 8-bit prescaler (with toggle outputs)
(The lower-order 8 bits can be used as PWM)
⢠Timer 6: 8-bit timer with a 6-bit prescaler (with toggle outputs)
⢠Timer 7: 8-bit timer with a 6-bit prescaler (with toggle outputs)
⢠Base timer
1) The clock is selectable from the subclock (32.768kHz crystal oscillation), system clock, and timer 0 prescaler
output.
2) Interrupts are programmable in 5 different time schemes
3) The base timer is unavailable when the CF oscillator circuit is selected
ï®SIO
⢠SIO0: 8-bit Synchronous serial interface
1) LSB first/MSB first mode selectable
2) Built-in 8-bit baudrate generator (maximum transfer clock cycle=4/3tCYC)
⢠SIO1: 8-bit asynchronous/synchronous serial interface
Mode 0: Synchronous 8-bit serial I/O (2- or 3-wire configuration, 2 to 512 tCYC transfer clocks)
Mode 1: Asynchronous serial I/O (half-duplex, 8 data bits, 1 stop bit, 8 to 2048 tCYC baudrates)
Mode 2: Bus mode 1 (start bit, 8 data bits, 2 to 512 tCYC transfer clocks)
Mode 3: Bus mode 2 (start detect, 8 data bits, stop detect)
ï®UART
⢠Full Duplex
⢠7/8/9 bit data bits selectable
⢠1 Stop bit (2 bits in continuous data transmission)
⢠Built-in baudrate generator
ï®AD Converter: 10 bits/8 bits à 10 channels (internal: 2 channels)
⢠10/8 bits AD converter resolution selectable
⢠Auto start function (It links an interrupt factor of MCPWM)
No.A1828-2/25
|
▷ |