CM2030 Datasheet, PDF (11/17 Pages) California Micro Devices Corp – HDMI Transmitter Port Protection and Interface Device

CM2030
VF
VESD
VESD
VCL
RDYN
ILEAK
CIN, TMDS
∆CIN, TMDS
CMUTUAL
CIN, DDCOUT
CIN, CECOUT
CIN, HPOUT
(5V_Supply-0.5V)
DDC_OUT to 5.0V, Bus
Capacitance = 1500pF
Diode Forward Voltage
IF = 8mA, TA = 25°C
Top Diode
0.6 0.85 0.95 V
Bottom Diode
0.6 0.85 0.95 V
ESD Withstand Voltage (IEC) Pins 4, 7, 10, 13, 20, 21, 22, 23, 24, ±8
kV
27, 30, 33, TA = 25°C; Note 2
ESD Withstand Voltage
Pins 1, 2, 16, 17, 18, 19, 37, 38, TA ±2
kV
(HBM)
= 25°C
Channel Clamp Voltage
TA=25°C, IPP = 1A, tP = 8/20µS;
Positive Transients
Note 5
11.0
V
Negative Transients
2.0
V
Dynamic Resistance
TA=25°C, IPP = 1A, tP = 8/20µS
Positive Transients
Any I/O pin to Ground; Note5
1.4
Ω
Negative Transients
0.9
Ω
TMDS Channel Leakage
TA = 25°C
0.01 1
µA
Current
TMDS Channel Input
5V_SUPPLY=5.0V, Measured at
0.9 1.2 pF
Capacitance
1MHz, VBIAS=2.5V
TMDS Channel Input
5V_SUPPLY=5.0V, Measured at
0.05
pF
Capacitance Matching
1MHz, VBIAS=2.5V; Note 4
Mutual Capacitance between 5V_SUPPLY=0V, Measured at
0.07
pF
signal pin and adja cent signal 1MHz, VBIAS=2.5V
pin
Level Shifting Input Capaci 5V_SUPPLY=0V,
10
pF
tance, Capacitance to GND Measured at 100KHz, VBIAS=2.5V
Level Shifting Input Capaci 5V_SUPPLY=0V,
10
pF
tance, Capacitance to GND Measured at 100KHz,
VBIAS=1.65V
Level Shifting Input Capaci 5V_SUPPLY=0V,
10
pF
tance, Capacitance to GND Measured at 100KHz,
VBIAS=2.5V
Note 1: Operating Characteristics are over Standard Operating Conditions unless otherwise specified.
Note 2: Standard IEC61000-4-2, C_DISCHARGE=150pF, Ω R_DISCHARGE=330 , 5V_SUPPLY=5V, 3.3V_SUPPLY=3.3V, LV_SUPPLY=3.3V,
GND=0V.
Note 3: Human Body Model per MIL-STD-883, Method 3015, C_DISCHARGE=100pF, Ω, R_DISCHARGE=1.5k 5V_SUPPLY=5V,
3.3V_SUPPLY=3.3V, LV_SUPPLY=3.3V, GND=0V.
Note 4: Intra-pair matching, each TMDS pair (i.e. D+, D–)
Note 5 These measurements performed with no external capacitor on V_P (V_P floating)
Note 6: These static measurements do not include AC activity on controlled I/O lines.
Note 7: This measurement does not inclue supply current for the 120µA current source on the CEC pin.
Rev. 5 | Page 11 of 17 | www.onsemi.com