|
AMIS-52150 Datasheet, PDF (1/21 Pages) AMI SEMICONDUCTOR – Low-Power Transceiver with Clock and Data Recovery | |||
|
AMIS-52150
LowÂpower Transceiver
with Clock and Data
Recovery
Introduction
The AMISâ52150 is a cost-effective, ultra-low power single-chip
wireless transceiver. It combines the proven Amplitude Shift
Key/On-Off Key (ASK/OOK) modulation technology of the
AMISâ52050 with data clock recovery.
Based on key features, such as dual independent receive channels,
Quick Start crystal oscillator, Sniff Mode signal acquisition, and data
clock recovery, the AMISâ52150 is ideally suited for a wide range of
applications, including point-to-point wireless data links,
cost-optimized wireless monitor solutions, and very low power remote
wireless sensors, among others.
http://onsemi.com
SSOPâ20
CASE TBD
Key Features
ï· Data Clock Recovery
ï· Auto Slicing of Data
ï· Very Low-power Single-chip Transceiver
ï· Minimal External Components
ï· Low-power RC Oscillator
ï· Quick Start Crystal Oscillator
ï· Ultra-low Power RF Sniff Mode, with Wake-up on
RSSI
ï· Internal Trim Functions Reduce External Component
Requirements
ï· I2C Control Interface
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 20 of this data sheet.
ï· Serial TX/RX Data Port
ï· Clock Generation for an External Microprocessor
ï· Wake-up on RSSI
ï· Antenna Diversity Dual Receiver
ï· Internal VCO/PLL Tuning Varactor
ï· Wake-up Interrupt to External Controller
ï· These Devices are Pb-Free and are RoHS Compliant
Technical Features
ï· Operating Frequency Range:
ï¨ Quick Start, from 350 MHz to 448 MHz
ï¨ Non-quick Start, from 300 MHz to 768 MHz
ï· TX Output Power: +12 dBm
ï· RX Sensitivity:
ï¨ Sniff Mode: â93 dBm Minimum
ï¨ Receive: â117 dBm Minimum @ 1 kbps, with CDR
ï· Data Rate:
ï¨ 1â8 kbps with Manchester Coding
ï¨ 1â16 kbps with NRZ Data
ï· Power Requirements:
ï¨ Receive: 7.5 mA (Continuous)
ï¨ Transmit: 25 mA @ Full Power (50% Duty-cycle)
ï¨ Sniff Mode: 75 mA (One Percent Duty-cycle)
ï¨ Standby: 500 nA (RC Oscillator Running)
ï· Operating Voltage: 2.3 V to 3.6 V
ï· Modulation: ASK/OOK
ï· Xtal Start Time: 15 ms (Quick Start)
ï· Sniff Mode Polling: 0.5 ms to 16 s
(0.5 ms or 64 ms Steps)
ï· PLL Lock Time: < 50 ms
ï· Selectable Data Filter: Up to 20 kHz
ï· Internal Trim Functions:
ï¨ TX Power (â3 to +12 dBm)
ï¨ Antenna Impedance Matching (Two Independent
Channels)
ï¨ Xtal, for Frequency and Quick Start
ï¨ RC Oscillator Frequency
ï¨ Sniff Mode, for Data Threshold
ï¨ Data slice
ï· Clock and Data Recovery (Reduced Data Jitter)
ï· I2C Interface: Control Bus
ï· Serial Interface: Data Input/Output
ï· Low Frequency IF
ï· Internal IF Filtering
ï· Package: 20-lead, 209 mm SSOP
ï£ Semiconductor Components Industries, LLC, 2013
1
July, 2013 â Rev. 8
Publication Order Number:
AMISâ52150/D
|
▷ |