E3SCT11D5M Datasheet, PDF (2/10 Pages) Omron Electronics LLC – Oil-resistant, Long-range Photoelectric Sensor with Metal Housing

E3S-C
Accessories (Order Separately)
Slits (A Slit is not provided with Through-beam Sensors. Order a Slit separately if required.) (Refer to Dimensions on page 10.)
Slit width
0.5 mm × 11 mm
1 mm × 11 mm
2 mm × 11 mm
4 mm × 11 mm
Sensing
distance
1.8 m
3.5 m
7m
15 m
Minimum detect-
able object
(typical)
0.5-mm dia.
1-mm dia.
2-mm dia.
2.6-mm dia.
Model
E39-S61
Quantity
Remarks
1 set each for
Emitter and Re-
ceiver
(8 Slits total)
(Snap-in Long Slit)
Can be used with the E3S-CT@1(-M1J)
Through-beam Sensor. Refer to page 10.
Reflectors (Reflector required for Retroreflective Sensors)
A Reflector is provided with the E39-R1 Sensor. For other Sensors, order a reflector separately if required. (Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.)
Name
Reflectors
Small Reflectors
Tape Reflectors
Sensing distance (typical)
3 m (rated value)
4m
1.5 m
750 mm
700 mm (50 mm)*
1,100 mm (100 mm)*
1,400 mm (100 mm)*
Model
E39-R1
E39-R2
E39-R3
E39-R4
E39-RS1
E39-RS2
E39-RS3
Quantity
1
1
1
1
1
1
1
Remarks
Provided with the E3S-CR@1 (-M1J) Retro-reflective Sensor.
---
---
---
Enables MSR function.
Note: 1. When using any reflector other than the provided one, use a sensing distance of approximately 0.7 times the typical value as a guide.
2. Refer to Reflectors on E39-L/F39-L/E39-S/E39-R for details.
* Values in parentheses indicate the minimum distance required between the Sensor and Reflector.
Mounting Brackets
Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required. (Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.)
Appearance
Model
Quantity
Remarks
E39-L102
1
Provided with Horizontal Models.
E39-L103
E39-L85
E39-L86
1
Provided with Vertical Models.
1
Mounting bracket for changing from E3S-
@@@@@42/44 to E3S-C Vertical Models.
1
Mounting bracket for changing from E3S-
@@@@@43 to E3S-C Vertical Models.
E39-L87
1
---
Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter.
2. Refer to Mounting Brackets on E39-L/F39-L/E39-S/E39-R for details.
Sensor I/O Connectors
(Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) (Refer to Dimensions on XS2.)
Cable
Standard
Appearance
Straight
L-shape
Cable type
2m
5m
3-wire
2m
5m
Model
XS2F-D421-DC0-A
XS2F-D421-GC0-A
XS2F-D422-DC0-A
XS2F-D422-GC0-A
Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter.
2. For details on Sensor I/O Connectors and cables such as vibration-proof robot cables, refer to Introduction to Sensor I/O Connectors.
2