E2E-X5ME2-M1 Datasheet, PDF (12/48 Pages) Omron Electronics LLC – A New Series of Easy-to-use and Tough E2E/E2E2 Models Long-size E2E2 Proximity Sensor Conforms to CENELEC

AC/DC 2-wire Models
Size
M12
M18
M30
Type
Shielded
Item
E2E-X3T1
E2E-X7T1
E2E-X10T1
Sensing distance
3 mm ±10%
7 mm ±10%
10 mm ±10%
Set distance
0 to 2.4 mm
0 to 5.6 mm
0 to 8.0 mm
Differential travel
10% max. of sensing distance
Sensing object
Ferrous metal (The sensing distance decreases with non-ferrous metal, refer to Engineering Data.)
Standard sensing object
Iron, 12 x 12 x 1 mm
Iron, 18 x 18 x 1 mm
Iron, 30 x 30 x 1 mm
Response speed
DC
(See note 1.)
AC
1.0 kHz
25 Hz
0.5 kHz
0.4 kHz
Power supply voltage
24 to 240 VDC (20 to 264 VDC)/48 to 240 VAC (40 to 264 VAC)
(operating voltage range) (See note 2.)
Leakage current
1 mA DC max., 2 mA AC max.
Control output
Load current 5 to 100 mA
Residual
voltage
6.0 VDC max. (Load current: 100 mA, Cable length: 2 m)
10 VAC max. (Load current: 5 mA, Cable length: 2 m)
Indicator
Operation indicator (red LED), setting indicator (green LED)
Operation mode
(with sensing object approaching)
NO
For details, refer to Timing Charts.
Protection circuits
Output load short-circuit protection (at 20 to 40 VDC), Surge suppressor
Ambient temperature
Operating: –25°C to 70°C, Storage: –40°C to 85°C (with no icing or condensation)
Ambient humidity
Operating/Storage: 35% to 95% (with no condensation)
Temperature influence
±10% max. of sensing distance at 23°C in the temperature range of –25°C to 70°C
Voltage influence
±1% max. of sensing distance in the rated voltage range ±15%
Insulation resistance
50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength
4,000 VAC at 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
1,000 m/s² 10 times each in X, Y, and Z directions
Degree of protection
IEC 60529 IP67
In-house standard for oil resistance (former JEM standard equivalent to IP67g) (See note 3.)
Connection method
Pre-wired Models (standard length 2 m)
Weight (packed state)
Approx. 80 g
Approx. 140 g
Approx. 190 g
Material
Case
Brass-nickel plated
Sensing surface PBT (polybutylene terephthalate)
Clamping nuts Brass-nickel plated
Toothed washer Iron-zinc plated
Accessories
Instruction manual
Note 1. The response speed is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard
sensing object, and a set distance of half the sensing distance.
2. Power supply voltage waveform: Use a sine wave for the power supply. Using a rectangular AC power supply may result in faulty reset.
3. This OMRON in-house standard confirms resistance to cutting and other oils. It is equivalent to the former JEM standard.
12
E2E/E2E2 Cylindrical Proximity Sensor