LMH6582_0708 Datasheet, PDF (4/16 Pages) National Semiconductor (TI) – 16x8 550MHz Analog Crosspoint Switch, Gain of 1

Symbol
Parameter
Conditions
TCV_OS
I_B
TCI_B
V_O
V_O
PSRR
Output Offset Voltage Average
Drift
Input Bias Current
Input Bias Current Average Drift
Output Voltage Range
Output Voltage Range
Power Supply Rejection Ratio
I_CC
Positive Supply Current
I_EE
Negative Supply Current
Tri State Supply Current
XTLK
DC Crosstalk
ISOL
DC Off Isloation
Miscellaneous Performance
R_IN
C_IN
R_O
R_O
CMVR
Input Resistance
Input Capacitance
Output Resistance
Output Resistance
Input Common Mode Voltage
Range
I_O
Output Current
Digital Control
V_IH
V_IL
V_OH
V_OL
T_S
T_H
(Note 10)
Non-Inverting (Note 9)
Non-Inverting (Note 10)
R_L = 100Ω
R_L = ∞
R_L = ∞
R_L = ∞
R_L = ∞
RST pin > 2.0V
DC, Channel to Channel
DC
Non-Inverting
Non-Inverting
Closed Loop, Enabled
Disabled
Sourcing, V_O = 0 V
Input Voltage High
Input Voltage Low
Output Voltage High
Output Voltage Low
Setup Time
Hold Time
Min
(Note 8)
Typ
(Note 7)
38
Max
(Note 8)
Units
µV/°C
±2.9
±2.93
42
−58
−60
−5
−12
±3.1
±3.2
45
110
104
20
−90
−90
−12
µA
nA/°C
V
V
dB
125
mA
120
mA
30
mA
dBc
dBc
100
kΩ
1
pF
300
mΩ
70
kΩ
±3.1
V
±60
±70
mA
2.0
V
0.8
V
>2.4
V
<0.4
V
5
ns
5
ns
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications, see the Electrical Characteristics tables.
Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)
Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 3: The maximum output current (I_OUT) is determined by device power dissipation limitations.
Note 4: The maximum power dissipation is a function of T_J(MAX), θ_JA. The maximum allowable power dissipation at any ambient temperature is
P_D = (T_J(MAX) – T_A)/ θ_JA. All numbers apply for packages soldered directly onto a PC Board.
Note 5: Electrical Table values apply only for factory testing conditions at the temperature indicated. No guarantee of parametric performance is indicated in the
electrical tables under conditions different than those tested.
Note 6: Slew Rate is the average of the rising and falling edges.
Note 7: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 8: Room Temperature limits are 100% production tested at 25°C. Factory testing conditions result in very limited self-heating of the device such that T_J =
T_A. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods.
Note 9: Negative input current implies current flowing out of the device.
Note 10: Drift determined by dividing the change in parameter at temperature extremes by the total temperature change.
Note 11: This parameter is guaranteed by design and/or characterization and is not tested in production.
Ordering Information
Package
64-Pin QFP
Part Number
LMH6582YA
Package Marking
LMH6582YA
Transport Media
160 Units/Tray
NSC Drawing
VXE64A
www.national.com
4