THS4509 Datasheet, PDF (33/42 Pages) Texas Instruments – WIDEBAND, LOW NOISE, LOW DISTORTION FULLY DIFFERENTIAL AMPLIFIER

THS4509
www.ti.com
SLOS454H – JANUARY 2005 – REVISED NOVEMBER 2009
Table 4. THS4509 EVAL1 EVM Bill of Materials
ITEM
1
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
20
DESCRIPTION
CAP, 10.0 μF, Ceramic, X5R, 6.3 V
CAP, 0.1 μF, Ceramic, X5R, 10 V
CAP, 0.22 μF, Ceramic, X5R, 6.3 V
OPEN
OPEN
Resistor, 49.9 Ω, 1/16 W, 1%
Resistor, 69.8 Ω, 1/16 W, 1%
Resistor, 86.6 Ω, 1/16 W, 1%
Resistor, 100 Ω, 1/16 W, 1%
Resistor, 348 Ω, 1/16 W, 1%
Transformer, RF
Jack, banana receptance, 0.25" diameter
hole
OPEN
Connector, edge, SMA PCB Jack
Test point, Red
IC, THS4509
Standoff, 4-40 HEX, 0.625" length
SCREW, PHILLIPS, 4-40, 0.250"
Printed circuit board
SMD
SIZE
0805
0402
0402
0402
0402
0402
0402
0402
0402
0402
REFERENCE
DESIGNATOR
C3-C6
C9-C14
C15
C1, C2, C7, C8
R9, R10
R12
R1, R2, R11
R7, R8
R3, R4
R5, R6
T1
J4, J5, J6
J1, J7, J8
J2, J3
TP1, TP2, TP3
U1
PCB
QTY
4
6
1
4
2
1
3
2
2
2
1
3
3
2
3
1
4
4
1
MANUFACTURER
PART NUMBER
(AVX) 08056D106KAT2A
(AVX) 0402ZD104KAT2A
(AVX) 04026D224KAT2A
(KOA) RK73H1ETTP49R9F
(KOA) RK73H1ETTP69R8F
(KOA) RK73H1ETTP86R6F
(KOA) RK73H1ETTP1000F
(KOA) RK73H1ETTP3480F
(MINI-CIRCUITS) ADT1-1WT
(HH SMITH) 101
(JOHNSON) 142-0701-801
(KEYSTONE) 5000
(TI) THS4509RGT
(KEYSTONE) 1808
SHR-0440-016-SN
(TI) EDGE# 6468901
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input and output voltage ranges as specified in the table provided
below.
INPUT RANGE, V_S+ TO V_S–
Input Range, V_I
Output Range, V_O
3.0 V TO 6.0 V
3.0 V to 6.0 V NOT TO EXCEED V_S+ or V_S–
3.0 V to 6.0 V NOT TO EXCEED V_S+ or V_S–
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If
there are questions concerning the input range, please contact a TI field representative prior to connecting the
input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible
permanent damage to the EVM. Please consult the product data sheet or EVM user's guide (if user's guide is
available) prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than +30°C. The EVM is
designed to operate properly with certain components above +50°C as long as the input and output ranges are
maintained. These components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors. These types of devices can be identified using the EVM schematic
located in the material provided. When placing measurement probes near these devices during operation, please
be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
Copyright © 2005–2009, Texas Instruments Incorporated
Product Folder Link(s): THS4509
Submit Documentation Feedback
33