LMH6552_14 Datasheet, PDF (3/32 Pages) Texas Instruments – 1.5 GHz Fully Differential Amplifier

LMH6552
www.ti.com
SNOSAX9H – APRIL 2007 – REVISED MARCH 2013
±5V Electrical Characteristics ⁽¹⁾
Unless otherwise specified, all limits are ensured for T_A = 25°C, V⁺ = +5V, V^− = −5V, A_V= 1, V_CM = 0V, R_F = R_G = 357Ω, R_L =
500Ω, for single ended in, differential out. Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min ⁽²⁾ Typ ⁽³⁾ Max ⁽²⁾
Units
AC Performance (Differential)
SSBW
Small Signal −3 dB Bandwidth ⁽²⁾
LSBW
Large Signal −3 dB Bandwidth
0.1 dB Bandwidth
Slew Rate
Rise/Fall Time, 10%-90%
V_OUT = 0.2 V_PP, A_V = 1, R_L = 1 kΩ
V_OUT = 0.2 V_PP, A_V = 1
V_OUT = 0.2 V_PP, A_V = 2
V_OUT = 0.2 V_PP, A_V = 4
V_OUT = 0.2 V_PP, A_V = 8
V_OUT = 2 V_PP, A_V = 1, R_L = 1 kΩ
V_OUT = 2 V_PP, A_V = 1
V_OUT = 2 V_PP, A_V = 2
V_OUT = 2 V_PP, A_V = 4
V_OUT = 2 V_PP, A_V = 8
V_OUT = 0.2 V_PP, A_V = 1
4V Step, A_V = 1
2V Step
1500
1000
930
810
590
1250
950
820
740
590
450
3800
600
MHz
MHz
MHz
V/μs
ps
0.1% Settling Time
2V Step
10
ns
Overdrive Recovery Time
V_IN = 1.8V to 0V Step, A_V = 5 V/V
6
Distortion and Noise Response
HD2
2^nd Harmonic Distortion
V_OUT = 2 V_PP, f = 20 MHz, R_L = 800Ω
−92
V_OUT = 2 V_PP, f = 70 MHz, R_L = 800Ω
−74
HD3
3^rd Harmonic Distortion
V_OUT = 2 V_PP, f = 20 MHz, R_L = 800Ω
−93
V_OUT = 2 V_PP, f = 70 MHz, R_L = 800Ω
−84
IMD3
Two-Tone Intermodulation
f ≥ 70 MHz, Third Order Products, V_OUT =
−87
2 V_PP Composite
Input Noise Voltage
f ≥ 1 MHz
1.1
ns
dBc
dBc
dBc
nV/√Hz
Input Noise Current
f ≥ 1 MHz
19.5
pA/√Hz
Noise Figure (See Figure 48)
Input Characteristics
I_BI
Input Bias Current ⁽⁴⁾
I_Boffset
Input Bias Current Differential
(3)
50Ω System, A_V = 9, 10 MHz
V_CM = 0V, V_ID = 0V, I_Boffset = (I_B^− - I_B⁺)/2
10.3
dB
60
110
µA
2.5
18
µA
CMRR
R_IN
C_IN
CMVR
Common Mode Rejection Ratio ⁽³⁾
Input Resistance
DC, V_CM = 0V, V_ID = 0V
Differential
Input Capacitance
Differential
Input Common Mode Voltage Range CMRR > 38 dB
80
dBc
15
Ω
0.5
pF
±3.5
±3.8
V
Output Performance
Output Voltage Swing ⁽³⁾
I_OUT
Linear Output Current ⁽³⁾
Differential Output
V_OUT = 0V
14.8
15.4
V_PP
±70
±80
mA
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T_J = T_A. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where T_J > T_A. See Application Information for information on temperature de-rating of this device."
Min/Max ratings are based on product characterization and simulation. Individual parameters are tested as noted.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using Statistical
Quality Control (SQC) methods.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(4) I_BI is referred to a differential output offset voltage by the following relationship: V_OD(offset) = I_BI*2R_F
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMH6552