N08L083WC2C Datasheet, PDF (3/9 Pages) NanoAmp Solutions, Inc. – 8Mb Ultra-Low Power Asynchronous CMOS SRAM 1024K × 8 bit

NanoAmp Solutions, Inc.
N08L083WC2C
Advance Information
Absolute Maximum Ratings
Item
Symbol
Rating
Unit
Voltage on any pin relative to V_SS
Voltage on V_CC Supply Relative to V_SS
Power Dissipation
Storage Temperature
Operating Temperature
Soldering Temperature and Time
V_IN,OUT
–0.3 to V_CC+0.3
V
V_CC
–0.3 to 4.5
V
P_D
500
mW
T_STG
–65 to 150
o_C
T_A
-40 to +85
o_C
T_SOLDER
260^oC, 10sec
o_C
Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional oper-
ation of the device at these or any other conditions above those indicated in the operating section of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Item
Symbol
Test Conditions
Min. _Typ¹ Max Unit
Supply Voltage
Data Retention Voltage
Input High Voltage
Input Low Voltage
Output High Voltage
Output Low Voltage
Input Leakage Current
Output Leakage Current
Read/Write Operating Supply Current
@ 1 µs Cycle Time²
Read/Write Operating Supply Current
@ fmax
Maximum Standby Current
Maximum Data Retention Current
V_CC
V_DR
Chip Disabled
Vcc = 2.2V to 2.7V
V_IH
Vcc = 2.7V to 3.6V
Vcc = 2.2V to 2.7V
V_IL
Vcc = 2.7V to 3.6V
V_OH
I_OH = -0.1mA, Vcc = 2.2V
I_OH = -1.0mA, Vcc = 2.7V
V_OL
I_OL = 0.1mA, Vcc = 2.2V
I_OL = 2.1mA, Vcc = 2.7V
I_LI
V_IN = 0 to V_CC
I_LO
V_OUT = 0 to V_CC
Output Disabled
I_CC1
I_CC2
I_SB1
V_CC=3.6 V, V_IN=V_IH or V_IL
Chip Enabled, I_OUT = 0
-L
V_CC=3.6 V, V_IN=V_IH or V_IL Chip
Enabled, I_OUT = 0
-L
V_IN = V_CC or 0V
Chip Disabled
t_A= 85^oC, V_CC = 3.6 V
-L
I_DR
Vcc = 1.5V, CE ≥ Vcc - 0.2V,
VIN ≥ Vcc - 0.2V or VIN ≤ 0.2V _-L
2.2 3.0 3.6 V
1.5
V
1.8
V_CC+0.3
V
2.2
V_CC+0.3
-0.3
0.6
V
-0.3
0.8
2.0
V
2.4
0.4
V
0.4
-1
1 µA
-1
1 µA
1.5 3.0
mA
1.5 3.0
12.0 20.0
mA
12.0 15.0
2.0 20
µA
2.0
8
10
µA
4
1. Typical values are measured at Vcc=Vcc Typ., T_A=25°C and not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive
output capacitance expected in the actual system.
Stock No. 23379-A
3
The specifications of this device are subject to change without notice. For latest documentation see http://www.nanoamp.com.