LSN2A Datasheet, PDF (2/15 Pages) Murata Manufacturing Co., Ltd. – Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters

LSN2 Series
Non-isolated, DOSA-SIP, 6/10/16A
Selectable-Output DC/DC Converters
PERFORMANCE SPECIFICATIONS AND ORDERING GUIDE c
Output
Root Model i
VOUT
(Volts)
IOUT
(Amps)
Power
(Watts)
R/N (mVp-p) d
Typ.
Max.
LSN2-T/6-W3
0.75-3.3 6
19.8
25
40
LSN2-T/6-D12
0.75-5
6
30
15
25
LSN2-T/10-W3
0.75-3.3 10
33.0
15
25
LSN2-T/10-D12
0.75-5
10
50
30
75
LSN2-T/16-W3
0.75-3.3 16
52.8
25
50
LSN2-T/16-D12h 0.75-5
16
80
30
75
LSN2-T/30-D12
0.8-5
30
150
Input
Regulation e
Line
Load
VIN Nom. Range g IIN f
(Volts) (Volts) (mA/A)
Efficiency
Min.
Typ.
±0.075% ±0.055% 5
2.4-5.5 50/4.2 93.1% 94.3%
±0.3% ±0.3%
12
8.3-14 70/2.69 90% 93%
±0.3% ±0.3%
5
2.4-5.5 50/6.95 93% 95%
±0.3% ±0.3%
12
8.3-14 100/4.39 93% 95%
±0.3% ±0.3%
5
2.4-5.5 50/11.12 93% 95%
±0.3% ±0.3%
12
8.3-14 100/7.1 92% 94%
Please refer to the separate LSN2-T/30 data sheet.
Package
(Case/
Pinout)
B12, P69
B12, P69
B11, P68
B11, P68
B11, P68
B11, P68
➀ Typical at TA = +25°C under nominal line voltage and full-load conditions, unless noted. All models
are tested and specified with external 22μF tantalum input and output capacitors. These capacitors
are necessary to accommodate our test equipment and may not be required to achieve specified
performance in your applications. See I/O Filtering and Noise Reduction. “Nominal” output is 3.3V
(W3 models) or 5V (D12 models)
➁ Ripple/Noise (R/N) is tested/specified over a 20MHz bandwidth and may be reduced with external
filtering. See I/O Filtering and Noise Reduction for details.
➂ These devices have no minimum-load requirements and will regulate under no-load conditions. Regula-
tion specifications describe the output-voltage deviation as the line voltage or load is varied from its
nominal/midpoint value to either extreme.
➃ Nominal line voltage, no-load/full-load conditions.
➄ VIN must be t0.5V greater than VOUT.
➅ LSN2-TXX-D12 efficiencies are shown at 5VOUT.
➆ These are not complete model numbers. Please refer to the Part Number Structure when ordering.
PART NUMBER STRUCTURE
L SN2 - T / 16 - D12 N G - C
Output Configuration:
L = Unipolar
Low Voltage
Non-Isolated Through-hole
Nominal Output Voltage:
0.75-3.3 Volts (W3)
0.75-5 Volts (D12)
RoHS-6 hazardous substance compliant
Power Good Output:
Blank = Omitted
G = Installed
On/Off Polarity:
Blank = Positive polarity
N = Negative polarity
➂ These devices have no minimum-load requirements and will regu-
late under no-load conditions. Regulation specifications describe
the output-voltage deviation as the line voltage or load is varied
from its nominal/midpoint value to either extreme.
➃ Nominal line voltage, no-load/full-load conditions.
➄ VIN must be t0.5V greater than VOUT.
➅ LSN2-TXX-D12 efficiencies are shown at 5VOUT.
➆ These are not complete model numbers. Please refer to the
Part Number Structure when ordering.
Maximum Rated Output:
Current in Amps
Input Voltage Range:
D12 = 8.3-14 Volts (12V nominal)
W3 = 2.4-5.5 Volts (5V nominal)
Note:
Some model number combinations may
not be available. Contact Murata Power
Solutions for further information.
www.murata-ps.com
Technical enquiries email: [e-mail], tel: [phone]
MDC_LSN2.B06 Page 2 of 15