DEBB33A102KA2B Datasheet, PDF (16/83 Pages) Murata Manufacturing Co., Ltd. – Safety Standard Certified Ceramic Capacitors/ High Voltage Ceramic Capacitors

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
C85E.pdf
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
Jul.13,2011
Type KSYa/fKeHty/KSXtaSnpdeacrdifiCcaetritoifniesdaTnydpTeeKstYM/KeHth/KoXdsSpecifications and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Appearance No marked defect
Capacitance
Change
Within ±10%
Soldering
I.R.
9 Effect
(Non-Preheat)
Dielectric
Strength
1000MΩ min.
Per Item 6
4
Appearance No marked defect
Capacitance
Change
Within ±10%
Soldering
10 Effect
(On-Preheat)
I.R.
Dielectric
Strength
1000MΩ min.
Per Item 6
Appearance No marked defect
Test Method
As shown in the figure, the lead
wires should be immersed in
Thermal
,,^Capacitor
solder of 350±10°C or 260±5°C up
to 1.5 to 2.0mm from the root of
terminal for 3.5±0.5 sec. (10±1
sec. for 260±5°C).
Scre_,,en_{,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,M,,1too.l5t2e.n0mm}
Solder
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition*² for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition.*²
First the capacitor should be
stored at 120+0/-5°C for
60+0/-5 sec.
Then, as in the figure, the lead
wires should be immersed in
solder of 260+0/-5°C up to 1.5 to
Thermal
,,Capacitor
Scre_,,en_{,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,M,,1too.l5t2e.n0mm}
Solder
2.0mm from the root of terminal
for 7.5+0/-1 sec.
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition*² for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition.*²
11
Vibration
Resistance
Capacitance Within the specified tolerance
Char.
Specifications
D.F.
B, E
D.F.V2.5%
Q
F
D.F.V5.0%
SL
QU400+20C*¹(CF30pF)
QU1000 (CU30pF)
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1-minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz.
Apply for a total of 6 hrs., 2 hrs. each in 3 mutually
perpendicular directions.
Appearance No marked defect
Humidity
12
(Under
Steady
State)
Capacitance
Change
D.F.
Q
Char.
B
E, F
SL
Capacitance Change
Within ±10%
Within ±15%
Within ± 5%
Char.
B, E
F
SL
Specifications
D.F.V5.0%
D.F.V7.5%
QU275+5/2C*¹(CF30pF)
QU350
(CU30pF)
Set the capacitor for 500±12 hrs. at 40±2°C in 90 to 95%
relative humidity.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition.*²
I.R.
Dielectric
Strength
Appearance
3000MΩ min.
Per Item 6
No marked defect
Capacitance
Change
13
Humidity
Loading
D.F.
Q
Char.
B
E, F
SL
Capacitance Change
Within ±10%
Within ±15%
Within ± 5%
Char.
B, E
F
SL
Specifications
D.F.V5.0%
D.F.V7.5%
QU275+5/2C*¹(CF30pF)
QU350
(CU30pF)
Apply the rated voltage for 500±12 hrs. at 40±2°C in 90 to 95%
relative humidity.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition.*²
I.R.
3000MΩ min.
Dielectric
Strength
Per Item 6
*¹ "C" expresses nominal capacitance value (pF).
*² "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued on the following page.
14