D1U3CS-W-1300F-12-HX4EC Datasheet, PDF (3/5 Pages) Murata Power Solutions Inc. – 81mm Front End AC-DC Power Converter

D1U3CS-W-1300F-12-Hx4EC Series
81mm Front End AC-DC Power Converter
STATUS INDICATORS
Conditions
Standby Rail ON; Main Output OFF; AC Present & correct
Standby Rail ON; Main Output ON
Main Output overcurrent; undervoltage, overvoltage warning
FAN_FAULT; overtemperature; standby rail overcurrent, Main Output overcurrent or overvoltage
LED Status
Blinking Green
Solid Green
Blinking Amber
Red
EMISSIONS AND IMMUNITY
Characteristic
Input Current Harmonics
Voltage Fluctuation & Flicker
Conducted Emissions
ESD Immunity
Radiated Field Immunity
Electrical Fast Transients/Burst Immunity
Surge Immunity
RF Conducted Immunity
Magnetic Field Immunity
Voltage Dips & Interruptions
Standard
IEC/EN 61000-3-2
IEC/EN 61000-3-3
FCC 47 CFR Part 15
CSIPR 22/EN55022
IEC/EN 61000-4-2;
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
IEC/EN 61000-4-11
Compliance
Complies with Class A Limits
Complies
Class B
Level 3; Criteria A
Level 3; Criteria B
Level 3; Criteria B
Level 3; Criteria A
Level 3; Criteria A
3A/m; Criteria B
230Vin, 100% load, Phase 0°, Dip 100% Duration 10ms (A)
230Vin, 50% load, Phase 0°, Dip 100% Duration 20ms (VSB:A, V1:A)
230Vin, 100% load, Phase 0°, Dip 100% Duration > 12ms (VSB:A, V1:B)
OUTPUT CONNECTOR & SIGNAL INTERFACE
DC Output and Signal Connector: FCI# 51731-057-LF
D1
D2
D3
D4
D5
D6
C1
C2
C3
C4
C5
C6
PB1
PB2
PB3
PB4
PB5
PB6
B1
B2
B3
B4
B5
B6
A1
A2
A3
A4
A5
A6
NB: B4 is the shortest “last make, first break” sequenced signal pin
Blade Assignment
Function
Description
PB1, PB2, PB3
+12V GND Main Output Voltage, Return
PB4, PB5, PB6
+12V OUT
Main Output Voltage
Signal Pin Assignment Signal Name
Description
A1
PS_ON_L
An input pulled up via an internal 10K ohm to the Standby rail. When pulled low (via an open collector/drain
drive or connection to GND) the Main Output will be turned on/enabled)
A2
+12VRS_RETURN Main Output Remote Sense (-VE/Return)
A3
TEMP_OK
TTL compatible Logic HIGH provided when the temperature is within the allowable range of operation.
A4
PS_SEATED
Internally connected to GND; when the power module is correctly seated the corresponding mating
connector pin is grounded and therefore allows detection that the power module is in situ.
A5, B5, C5, D5
+VSB
Standby Voltage Output
A6, B6, C6, D6
+VSB GND Standby Voltage Output, Return/GND
B1
AC_OK
Incoming AC Source voltage “OK” (present and within operational limits)
B2
+12VRS
Main 12V output remote sense line
B3
+12V_ISHARE Main 12V output current share bus
This is the shortest “last make, first break” (last to mate in the sequence).
B4
PS_INHIBIT/PS_KILL
If left open circuit then the main output will be inhibited (no output).
When inserted in to the system slot this pin must be pulled “low” by the system to enable (turn on) the
Main output and only after all other pins are connected and the power module is correctly seated.
C1
SDA
I²C Serial Data Line
C2
SCL
I²C Serial Clock Line
Current (Amps per Pin)
30
30
N/A
N/A
N/A
2.0
2.0
N/A
N/A
N/A
N/A
N/A
N/A
www.murata-ps.com/support
D1U3CS-W-1300F-12-Hx4EC.A01 Page 3 of 5