PS21212 Datasheet, PDF (4/8 Pages) Mitsubishi Electric Semiconductor – TRANSFER-MOLD TYPE INSULATED TYPE

MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
PS21212
TRANSFER-MOLD TYPE
INSULATED TYPE
THERMAL RESISTANCE
Symbol
Parameter
Rth(j-c)Q
Rth(j-c)F
Rth(c-f)
Junction to case thermal
resistance
Contact thermal resistance
Condition
Inverter IGBT part (per 1/6 module)
Inverter FWDi part (per 1/6 module)
Case to fin, (per 1 module)
thermal grease applied
Limits
Min.
Typ.
Max. ^Unit
—
—
4.0
—
—
6.1
°C/W
—
—
0.067
ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted)
INVERTER PART
Symbol
Parameter
VCE(sat)
VEC
ton
trr
tc(on)
toff
tc(off)
ICES
Collector-emitter saturation
voltage
FWDi forward voltage
Switching times
Collector-emitter cut-off
current
Condition
VD = VDB = 15V
IC = 5A, Tj = 25°C
VCIN = 0V
IC = 5A, Tj = 125°C
Tj = 25°C, –IC = 5A, VCIN = 5V
VCC = 300V, VD = VDB = 15V
IC = 5A, Tj = 125°C, VCIN = 5V → 0V
Inductive load (upper-lower arm)
Note: ton, toff include delay time of the internal control
circuit
VCE = VCES
Tj = 25°C
Tj = 125°C
Limits
Min.
Typ.
Max. ^Unit
—
2.1
—
—
2.2
—
V
—
1.7
—
V
—
0.6
—
—
0.1
—
—
0.2
—
µs
—
1.1
—
—
0.35
—
—
—
1.0
—
—
10
mA
CONTROL (PROTECTION) PART
Symbol
Parameter
Condition
Limits
Min.
Typ.
Max. ^Unit
VD
Control supply voltage
Applied between VP1-VPC, VN1-VNC
13.5 15.0
16.5
V
VDB
Control supply voltage
ID
Circuit current
VFOH
VFOL
VFOsat
fPWM
Fault output voltage
PWM input frequency
Applied between VUFB-VUFS, VVFB-VVFS, VWFB-VWFS
VD = VDB= 15V, VP1-VPC, VN1-VNC
input = OFF
VUFB-VUFS, VVFB-VVFS, VWFB-VWFS
VD = VDB= 15V, VP1-VPC, VN1-VNC
input = ON
VUFB-VUFS, VVFB-VVFS, VWFB-VWFS
VSC = 0V, FO circuit : 10kΩ to 5V pull-up
VSC = 1V, FO circuit : 10kΩ to 5V pull-up
VSC = 1V, IFO = 15mA
TC ≤ 100°C, Tj ≤ 125°C
13.5
—
—
—
—
4.9
—
0.8
—
15.0
4.25
0.50
4.95
0.50
—
1.0
1.2
15
16.5
V
8.50 mA
1.00 mA
9.70 mA
1.00 mA
—
V
2.0
V
1.8
V
—
kHz
tdead
Allowable deadtime
Relates to corresponding input signal for blocking arm
shoot-through.
–20°C ≤ TC ≤ 100°C
3.0
—
—
µs
VSC(ref) Short circuit trip level
Tj = 25°C, VD = 15°C
(Note 2) _0.45
0.5
0.55
V
UVDBt
UVDBr
UVDt
UVDr
tFO
Vth(on)
Vth(off)
Vth(on)
Vth(off)
Supply circuit under-voltage
protection
Fault output pulse width (Note 3)
ON threshold voltage
OFF threshold voltage
ON threshold voltage
OFF threshold voltage
Trip level
Tj ≤ 125°C
Reset level
Trip level
Reset level
CFO = 22nF (connected between CFO–VNC)
H-side
Applied between:
UP, VP, WP-VPC
L-side
Applied between:
UN, VN, WN-VNC
10.0
—
10.5
—
10.3
—
10.8
—
1.0
1.8
0.8
1.4
2.5
3.0
0.8
1.4
2.5
3.0
12.0
V
12.5
V
12.5
V
13.0
V
—
ms
2.0
V
4.0
2.0
V
4.0
Note 2 : Short circuit protection is functioning only at the low-arms. Please select the value of the external shunt resistor such that the SC trip-
level is less than 8.5 A.
3 : Fault signal is output when the low-arms short circuit or control supply under-voltage protective functions operate. The fault output pulse-
width tFO depends on the capacitance value of CFO according to the following approximate equation : CFO = 12.2 ! 10^-6 ! tFO [F].
Aug. 1999