PIC16F716-I Datasheet, PDF (98/136 Pages) Microchip Technology – 8-bit Flash-based Microcontroller with A/D Converter and Enhanced Capture/Compare/PWM

PIC16F716
12.4 DC Characteristics: PIC16F716 (Industrial, Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Operating voltage VDD range as described in DC spec Section 12.1 “DC Charac-
teristics: PIC16F716 (Industrial, Extended)” and Section 12.4 “DC Character-
istics: PIC16F716 (Industrial, Extended)”.
Param
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
Input Low Voltage
VIL
I/O ports
D030
D030A
with TTL buffer
VSS
—
0.8
V 4.5V ≤ VDD ≤ 5.5V
VSS
— 0.15 VDD V otherwise
D031
with Schmitt Trigger buffer
VSS
—
0.2 VDD
V
D032
MCLR, OSC1 (in RC mode)
VSS
—
0.2 VDD
V
D033
OSC1 (in HS mode)
OSC1 (in XT and LP modes)
VSS
—
0.3 VDD
V (Note1)
VSS
—
0.6
V
Input High Voltage
VIH
I/O ports
—
D040
with TTL buffer
2.0
—
VDD
V 4.5V ≤ VDD ≤ 5.5V
D040A
0.25 VDD + —
VDD
V otherwise
0.8V
D041
with Schmitt Trigger buffer
0.8 VDD —
VDD
V For entire VDD range
D042
MCLR
0.8 VDD —
VDD
V
D042A
OSC1 (XT, HS and LP modes)
0.7 VDD —
VDD
V (Note1)
D043
OSC1 (in RC mode)
0.9 VDD —
VDD
V
D060
IIL
Input Leakage Current^{(2), (3)}
I/O ports
D061
D063
D070
MCLR, RA4/T0CKI
OSC1/CLKIN
IPURB PORTB weak pull-up current
—
—
±1
μA Vss ≤ VPIN ≤ VDD, Pin at
high-impedance
—
—
±500
nA Vss ≤ VPIN ≤ VDD, Pin configured as
analog input
—
—
±5
μA Vss ≤ VPIN ≤ VDD
—
—
±5
μA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc
modes
50
250
400
μA VDD = 5V, VPIN = VSS
Output Low Voltage
D080
VOL
I/O ports
—
—
0.6
V IOL = 8.5 mA, VDD = 4.5V, -40°C to
+85°C
—
—
0.6
V IOL = 7.0 mA, VDD = 4.5V, -40°C to
+125°C
D083
OSC2/CLKOUT (RC Osc mode)
—
—
0.6
V IOL = 1.6 mA, VDD = 4.5V, -40°C to
+85°C
—
—
0.6
V IOL = 1.2 mA, VDD = 4.5V, -40°C to
+125°C
Output High Voltage
D090
VOH
I/O ports⁽³⁾
VDD-0.7 —
—
V IOH = -3.0 mA, VDD = 4.5V, -40°C to
+85°C
VDD-0.7 —
—
V IOH = -2.5 mA, VDD = 4.5V, -40°C to
+125°C
D092
OSC2/CLKOUT (RC Osc mode)
VDD-0.7 —
—
V IOH = -1.3 mA, VDD = 4.5V, -40°C to
+85°C
VDD-0.7 —
—
V IOH = -1.0 mA, VDD = 4.5V, -40°C to
+125°C
D150* VOD Open-Drain High Voltage
—
—
8.5
V RA4 pin
Capacitive Loading Specs on Output Pins
D100 COSC2 OSC2/CLKOUT pin
—
—
15
pF In XT, HS and LP modes when external
clock is used to drive OSC1.
D101
CIO
All I/O pins and OSC2 (in RC mode)
—
—
50
pF
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.
Note 1: In RC Oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC^® be driven with
external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS41206B-page 96
© 2007 Microchip Technology Inc.